Dell PowerEdge 7250 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 102

background image

Terminal Mode Commands

81

Boot flags
(semi-volatile)

5

Data 1
[7] - 1b = Boot flags valid. The bit should be set to indicate that

valid flag data is present. This bit may be automatically cleared

based on the boot flag valid bit clearing parameter.
[6:0] - Reserved
BIOS support for the following flags is optional. If a given flag is

supported, it must cause the specified function to occur in order

for the implementation to be considered to be in conformity with

this specification.
The following parameters represent temporary overrides of the

BIOS default settings. BIOS should only use these parameters for

the single boot where these flags were set. If the bit is 0b, BIOS

should use its default configuration for the given option.
Data 2
[7]—1b = CMOS clear.
[6]—1b = Lock Keyboard.
[5:2] - Boot device selector.
0000b = No override.
0001b = Force PXE.
0010b = Force boot from default Hard-drive.
0011b = Force boot from default Hard-drive, request Safe Mode.
0100b = Force boot from default Diagnostic Partition.
0101b = Force boot from default CD/DVD.
0110b–1110b = Reserved.
1111b = Force boot from diskette/primary removable media.
[1]—1b = Screen Blank.
[0]—1b = Lock out Reset buttons.

Table C-5. Boot Option Parameters

(continued)

Parameter

Number

Parameter Data (non-volatile unless otherwise noted)

«
...
81
82
83
84
85
...
»

Содержание PowerEdge 7250







































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge 7250

Бренд: TRENDnet Страницы: 14

Бренд: Kontron Страницы: 110

UniServer R4300 G5

Бренд: H3C Страницы: 16

Бренд: B&B Electronics Страницы: 2

Бренд: Vxl Страницы: 19

Бренд: Synology Страницы: 24

8668 - Eserver xSeries 232

Бренд: IBM Страницы: 182

Бренд: MO-SYS Страницы: 26

Бренд: Cisco Страницы: 2

DL380 Gen 10 AI

Бренд: Bosch Страницы: 18

Бренд: Bosch Страницы: 48

Бренд: Bosch Страницы: 44

Бренд: 2Wire Страницы: 2

Бренд: QNAP Страницы: 203

Бренд: EVS Страницы: 198

Бренд: Kathrein Страницы: 16

Бренд: Kathrein Страницы: 16

Бренд: Kathrein Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды