Dell PowerEdge 7250 Скачать руководство пользователя страница 15

Страница: 15 / 102

Configuring Your Managed System

Configuring Your Managed System

In order to use the BMC Management Utility, you must first configure the necessary system BIOS,

network, and serial connection settings to enable access to the BMC.
In addition, to utilize the BMC Management Utility IPMI Serial functions, you must have a

working connection between the management station and the correct serial I/O port of the

managed system, using a null modem cable.
This section describes the basic procedures you must perform in order to prepare your BMC to be

accessed and managed using the BMC Management Utility. The following procedures are

described:

• BIOS Configuration
• Configuring Your BMC with the System Maintenance Utility (SMU)
• Configuring Your BMC with Server Administrator

BIOS Configuration

For most configurations you will need to configure specific BIOS settings before you can use the

BMC Management Utility. To configure the necessary system BIOS settings, your must enter the

System Setup utility.

NOTE:

For more information about configuring BIOS settings, see your system’s Product Guide.

Starting the System Setup Utility

To start Setup during the power-on sequence, follow these steps:

Press the power button on the front control panel of the system.

When POST shows the message

Hit <F2> if you want to run SETUP

press

<F2>. If the system has an administrator password configured, the system prompts you to

enter the password. If the system does not have a password configured, the main screen of the

BIOS Setup utility appears.

Navigating Setup Utility Screens

The BIOS Setup utility consists of five primary menus:

Main

Advanced

Security

System

Management

, and

Exit

. Each menu occupies a single screen and presents a list of menu items.

Some menu items are submenus, while others are settings that you can change from the screen.

Table 2-1 describes how to navigate the utility screens and menus.

Содержание PowerEdge 7250







































































































Результаты поиска

Содержание PowerEdge 7250

Отзывы:

Похожие инструкции для PowerEdge 7250

Бренды по названию

Популярные бренды

Dell PowerEdge 7250, Руководство пользователя

Результаты поиска

Содержание PowerEdge 7250

Отзывы:

Похожие инструкции для PowerEdge 7250

Бренды по названию

Популярные бренды