Dell PowerEdge 7250 Скачать руководство пользователя страница 84

Страница: 84 / 102

Terminal Mode Commands

www

.del

com |

ppo

rt.

ll.

Boot flags
(semi-volatile)

(continued)

Data 3
[7] - 1b = Lock out (power off/ sleep request) using the Power

Button.
[6:5] - Firmware (BIOS) Verbosity (Directs what appears on POST

display).
00b = System default.
01b = Request quiet display.
10b = Request verbose display.
11b = Reserved.
[4] - 1b = Force progress event traps. When set to 1b, the BMC

transmits PET traps for BIOS progress events to the LAN or

serial/modem destination for the session that set the flag. Since

this capability uses PET traps, this bit is ignored for connection

modes that do not support PET such as Basic Mode and Terminal

Mode.
[3] - 1b = User password bypass. When set to 1b, the managed

client’s BIOS boots the system and bypasses any user or boot

password that might be set in the system.
[2] - 1b = Lock Sleep Button. When set to 1b, directs BIOS to

disable the sleep button operation for the system, normally until

the next boot cycle.
[1:0] -00b = Console redirection occurs per BIOS configuration

setting.
01b = Suppress (skip) console redirection if enabled.
10b = Request console redirection be enabled.
11b = Reserved.

Table C-5. Boot Option Parameters

(continued)

Parameter

Number

Parameter Data (non-volatile unless otherwise noted)

Содержание PowerEdge 7250







































































































Результаты поиска

Содержание PowerEdge 7250

Отзывы:

Похожие инструкции для PowerEdge 7250

Бренды по названию

Популярные бренды

Dell PowerEdge 7250, Руководство пользователя

Результаты поиска

Содержание PowerEdge 7250

Отзывы:

Похожие инструкции для PowerEdge 7250

Бренды по названию

Популярные бренды