Dell PowerEdge 700 Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 94

background image

Back to Contents Page

Installing Drives

Dell™ PowerEdge™ 700 Systems Installation and Troubleshooting Guide

Connecting Drives

Front-Panel Drive Inserts

5.25-Inch Drives

Cabled SATA and SCSI Hard Drives

Hot-Plug SCSI Hard Drives

Installing a RAID Controller Card

Your system supports the following drives:

l

Up to two externally accessible 5.25-inch drives (typically CD and tape backup drives). A CD drive is standard in the first external drive bay, and a tape

backup device can be installed in the second external drive bay.

l

An externally accessible 3.5-inch diskette drive.

l

Up to four 1-inch SATA or SCSI hard drives.

Connecting Drives

Interface Cables

Most interface connectors are keyed for correct insertion. Keying ensures that the pin-1 wire in the cable connects to pin 1 in the connectors on both ends.
When you disconnect an interface cable, take care to grasp the cable connector, rather than the cable itself, to avoid stress on the cable.

Drive Cable Configurations

Your system can accommodate many different drive configurations, each with specific cable requirements.

shows the cable requirements for common

drive configurations.

Table 7-

1. Drive Cable Configuration

DC Power Cables

Each drive must connect to a DC power cable from the system power supply. These power cables are used for the 3.5-inch diskette drive, 5.25-inch devices,
and hard drives.

NOTE:

Installing SATA and SCSI hard drives in the same system is not supported.

Drives

Required Cable

Cable Connections

IDE CD, DVD, and CD-RW/DVD drives, and IDE and

SCSI tape drives (See

.)

40-pin IDE 2-drop cable or SCSI 1-

drop cable (terminated)

IDE drive and primary IDE connector on system board or the

SCSI tape device and the SCSI controller card

Up to two cabled SATA hard drives (See

7-pin SATA hard-drive cable (one

cable per drive)

SATA hard drives and SATA port connectors on the system

board

Three or four cabled SATA hard drives (See

One SATA hard-drive cable assembly

for up to four drives

SATA hard drives and SATA RAID controller card (when

available)

Up to four hot-plug SCSI hard drives (See

.)

38-cm (15-inch) 68-pin SCSI 1-drop

cable (unterminated)

SCSI backplane and the SCSI or RAID controller card

Up to four cabled (non-hot-plug) SCSI hard-drives

(See

.)

94-cm (37-inch) SCSI 4-drop cable

(terminated)

SCSI hard drives and SCSI RAID controller or SCSI controller

card

«
...
68
69
70
71
72
...
»

Содержание PowerEdge 700































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge 700

Flex System x440 Compute Node

Бренд: IBM Страницы: 584

Бренд: IBM Страницы: 142

DTS 4132.timeserver

Бренд: Mobatime Страницы: 108

Бренд: ICP DAS USA Страницы: 4

Бренд: Olive Страницы: 44

BocaVision WT120

Бренд: Boca Systems Страницы: 28

Бренд: TYAN Страницы: 87

Бренд: QNAP Страницы: 16

PRIMERGY econel 20

Бренд: Fujitsu Siemens Computers Страницы: 62

SPARC Enterprise M4000

Бренд: Fujitsu Siemens Computers Страницы: 162

Бренд: TRENDnet Страницы: 2

Бренд: TRENDnet Страницы: 2

TEW-P1UG - Wireless Print Server

Бренд: TRENDnet Страницы: 2

Бренд: TRENDnet Страницы: 15

Бренд: BushkaBlue Страницы: 30

Бренд: Supermicro Страницы: 78

Бренд: Xantech Страницы: 52

Бренд: 360 Systems Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды