Dell PowerEdge 700 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 94

background image

Back to Contents Page

Indicators and Codes

Dell™ PowerEdge™ 700 Systems Installation and Troubleshooting Guide

The system, applications, and operating systems can identify problems and alert you to them. Any of the following can indicate when the system is not
operating properly:

l

System indicators

l

System messages

l

Beep codes

l

Warning messages

l

Diagnostics messages

l

Alert messages

This section describes each type of message, lists the possible causes, and provides steps to resolve any problems indicated by a message. The system
indicators and features are illustrated in this section.

Front-Panel Indicators and Features

shows the front-panel features of the system.

describes the front-panel features.

Figure 2-1. Front Panel Features

Table 2-1. Front-

Panel Features and Indicators

Front-Panel Indicators and Features

System Beep Codes

Back-Panel Features

Warning Messages

NIC Indicator Codes

Diagnostics Messages

Hot-Plug SCSI Hard-Drive Indicator Codes

System Messages

Indicator or
Feature

Description

Power button

Turns system power off and on.

l

If you turn off the system using the power button and the system is running an ACPI-compliant operating system, the system can

perform an orderly shutdown before power is turned off. If the power button is pressed for more than 4 seconds, the system power
will turn off regardless of the current operating system state.

l

If the system is not running an ACPI-compliant operating system, power is turned off immediately after the power button is

pressed.

The power button is enabled in the System Setup program. When disabled, the button can only turn the system power on. For more

information, see your

User's Guide

and the operating system's documentation.

Power indicator

When the power indicator is on, the system is in a normal operating state. When the indicator is off, the system is off.

«
...
22
23
24
25
26
...
»

Содержание PowerEdge 700































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge 700

Бренд: Sollae Systems Страницы: 45

Бренд: TYAN Страницы: 136

Бренд: BRONKHORST Страницы: 19

PRIMEQUEST 3800E

Бренд: Fujitsu Страницы: 38

Бренд: Fujitsu Страницы: 36

Primergy BX2560 M1

Бренд: Fujitsu Страницы: 68

PRIMEQUEST 3000 Series

Бренд: Fujitsu Страницы: 44

Бренд: Fujitsu Страницы: 56

PRIMEQUEST 2800B3

Бренд: Fujitsu Страницы: 28

Бренд: Fujitsu Страницы: 35

PRIMERGY 10/40GbE Connection Blade 18/8+2

Бренд: Fujitsu Страницы: 71

Бренд: Fujitsu Страницы: 94

PRIMEQUEST 3800E2

Бренд: Fujitsu Страницы: 42

Бренд: Fujitsu Страницы: 104

PRIMERGY BX400 S1

Бренд: Fujitsu Страницы: 136

Бренд: Fujitsu Страницы: 94

PRIMEQUEST 2400E3

Бренд: Fujitsu Страницы: 148

Бренд: Fujitsu Страницы: 177

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды