Dell PowerEdge 700 Скачать руководство пользователя страница 5

Страница: 5 / 94

Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

Remove the bezel. See "

Removing the Bezel

" in "Troubleshooting Your System."

Lay the system on its right side.

Remove the cover. See "

Removing the Cover

" in "Troubleshooting Your System."

Remove the PSWD_EN jumper plug.

See

Figure A

-2

to locate the jumper on the system board.

Install the cover. See "

Replacing the Cover

" in "

Troubleshooting Your System

Stand the system upright.

Replace the bezel. See "

Installing the Bezel

" in "Troubleshooting Your System."

Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.

The existing passwords are not disabled (erased) until the system boots with the PSWD_EN jumper plug removed. However, before you assign a new
system and/or setup password, you must install the jumper plug.

10.

Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

11.

Remove the bezel. See "

Removing the Bezel

" in "Troubleshooting Your System."

12.

Lay the system on its right side.

13.

Remove the cover "

Removing the Cover

" in "Troubleshooting Your System."

14.

Install the PSWD_EN jumper plug.

See

Figure A

-2

to locate the jumper on the system board.

15.

Install the cover. See "

Replacing the Cover

" in "

Troubleshooting Your System

16.

Stand the system upright.

17.

Replace the bezel. See "

Installing the Bezel

" in "Troubleshooting Your System."

18.

Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.

19.

Assign a new system and/or setup password.

To assign a new passwords using the System Setup program, see "Assigning a System Password" in your

User's Guide

Back to Contents Page

CAUTION:

See your

System Information Guide

for complete information about safety precautions, working inside the computer, and protecting

against electrostatic discharge.

NOTE:

If you assign a new system and/or setup password with the jumper plug still removed, the system disables the new password(s) the next

time it boots.

Содержание PowerEdge 700































































































Результаты поиска

Содержание PowerEdge 700

Отзывы:

Похожие инструкции для PowerEdge 700

Бренды по названию

Популярные бренды

Dell PowerEdge 700, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание PowerEdge 700

Отзывы:

Похожие инструкции для PowerEdge 700

Бренды по названию

Популярные бренды