Dell PowerEdge 700 Скачать руководство пользователя страница 79

Страница: 79 / 94

Ensure that all cables are firmly connected and arranged so that they will not catch on the computer covers or block airflow inside the system.

Install the cooling shroud. See "

Installing the Cooling Shroud

" in "Installing System Options."

Install the cover. See "

Replacing the Cover

" in "Troubleshooting Your System."

Stand the system upright.

10.

Install the bezel. See "

Installing the Bezel

" in "Troubleshooting Your System."

11.

Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.

12.

Partition and logically format the hard drive. See the operating system documentation for more information.

13.

Install any required device drivers.

14.

Run the hard drive tests in the system diagnostics to determine whether the drive operates properly. See "

Running System Diagnostics

If the drive is connected to a SATA RAID controller card, see the RAID controller card documentation for information on testing the controller.

If the drive is connected to a SCSI controller card, run the SCSI controller tests and the hard drive tests in the system diagnostics. See "

Running System

Diagnostics

If the hard drive fails the hard drive tests or does not operate properly, see "

Getting Help

Hot-Plug SCSI Hard Drives

The drive bays in a system with an optional SCSI backplane board provide space for up to four 1-inch hot-plug hard drives. The hard drives plug into the SCSI
backplane board, which is connected to a SCSI RAID controller card. See

Figure 7

-10

Figure 7-10. Hot-Plug SCSI Hard Drives Connected to a SCSI RAID Controller Card

Содержание PowerEdge 700































































































Результаты поиска

Содержание PowerEdge 700

Отзывы:

Похожие инструкции для PowerEdge 700

Бренды по названию

Популярные бренды

Dell PowerEdge 700, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание PowerEdge 700

Отзывы:

Похожие инструкции для PowerEdge 700

Бренды по названию

Популярные бренды