manualshive.com logo in svg

Dell E70S, Инструкция по установке и обслуживанию

Dell E70S - товар с установочным и сервисным руководством. Получите бесплатное скачивание из manualshive.com. Руководство по эксплуатации и обслуживанию доступно для скачивания, чтобы помочь вам настроить и обслуживать свой продукт. Безопасно и легко скачивать с manualshive.com.

Поделиться
Скачать
background image

Chapter 1: About this document.................................................................................................... 8

Chapter 2: System overview..........................................................................................................9

Front view of the system.................................................................................................................................................. 9

Left control panel view................................................................................................................................................11
Right control panel view.............................................................................................................................................12

Rear view of the system.................................................................................................................................................. 13
Inside the system .............................................................................................................................................................. 17
Locating the Express Service Code and Service Tag............................................................................................... 19
System information label................................................................................................................................................. 20
Rail sizing and rack compatibility matrix......................................................................................................................24

Chapter 3: Initial system setup and configuration........................................................................25

Setting up the system......................................................................................................................................................25
iDRAC configuration......................................................................................................................................................... 25

Options to set up iDRAC IP address.......................................................................................................................25
Options to log in to iDRAC........................................................................................................................................ 26

Resources to install operating system..........................................................................................................................27

Options to download firmware ................................................................................................................................27
Options to download and install OS drivers .........................................................................................................28
Downloading drivers and firmware..........................................................................................................................28

Chapter 4: Minimum to POST and system management configuration validation......................... 29

Minimum configuration to POST ..................................................................................................................................29
Configuration validation...................................................................................................................................................29

Error messages............................................................................................................................................................ 30

Chapter 5: Installing and removing system components...............................................................31

Safety instructions.............................................................................................................................................................31
Before working inside your system............................................................................................................................... 32
After working inside your system.................................................................................................................................. 32
Recommended tools......................................................................................................................................................... 32
Cable routing...................................................................................................................................................................... 33
M.2 SSD module ...............................................................................................................................................................54

Removing the M.2 SSD module............................................................................................................................... 54
Installing the M.2 SSD module................................................................................................................................. 55

Optional front bezel..........................................................................................................................................................56

Removing the front bezel..........................................................................................................................................56
Installing the front bezel............................................................................................................................................ 57

System cover..................................................................................................................................................................... 58

Removing the system cover..................................................................................................................................... 58
Installing the system cover....................................................................................................................................... 59

Drive backplane cover......................................................................................................................................................60

Removing the drive backplane cover..................................................................................................................... 60

Contents

Contents

3

Содержание E70S















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E70S

LaCie Network Space MAX Datasheet preview
Network Space MAX
Бренд: LaCie Страницы: 2
360 Systems V2000 Series Operation Manual preview
V2000 Series
Бренд: 360 Systems Страницы: 117
Aastra AXD Installation And Maintenance Manual preview
AXD
Бренд: Aastra Страницы: 502
Surveon EonServ 5000 Series User Manual preview
EonServ 5000 Series
Бренд: Surveon Страницы: 33
Supero SUPERSERVER 6027R-TRF User Manual preview
SUPERSERVER 6027R-TRF
Бренд: Supero Страницы: 102
Jatheon PnC 100 Installation & Administrators Manual preview
PnC 100
Бренд: Jatheon Страницы: 52
PRIMERGY BX600 S2 Hardware Manual preview
BX600 S2
Бренд: PRIMERGY Страницы: 87
MSI E7210 Master-FARM User Manual preview
E7210 Master-FARM
Бренд: MSI Страницы: 34
Acrosser Technology AND-APL1E Series User Manual preview
AND-APL1E Series
Бренд: Acrosser Technology Страницы: 42
Fujitsu PRIMEQUEST 3800E System Configuration Manual preview
PRIMEQUEST 3800E
Бренд: Fujitsu Страницы: 38
Fujitsu PRIMERGY B900 Reference Manual preview
PRIMERGY B900
Бренд: Fujitsu Страницы: 36
Fujitsu Primergy BX2560 M1 Operating Manual preview
Primergy BX2560 M1
Бренд: Fujitsu Страницы: 68
Fujitsu PRIMEQUEST 3000 Series Getting Started Manual preview
PRIMEQUEST 3000 Series
Бренд: Fujitsu Страницы: 44
Fujitsu PRIMERGY User Manual preview
PRIMERGY
Бренд: Fujitsu Страницы: 56
Fujitsu PRIMEQUEST 2800B3 System Configuration Manual preview
PRIMEQUEST 2800B3
Бренд: Fujitsu Страницы: 28
Fujitsu PRIMERGY 870 Technical Manual preview
PRIMERGY 870
Бренд: Fujitsu Страницы: 35
Fujitsu PRIMERGY 10/40GbE Connection Blade 18/8+2 Function Manual preview
PRIMERGY 10/40GbE Connection Blade 18/8+2
Бренд: Fujitsu Страницы: 71
Fujitsu PRIMERGY 300 Operating Manual preview
PRIMERGY 300
Бренд: Fujitsu Страницы: 94

Бренды по названию

Популярные бренды

Загрузить еще бренды