Dell E70S Скачать руководство пользователя страница 228 | Manualshive

Страница: 228 / 238

background image

Table 80. iDRAC Direct LED indicator codes (continued)

iDRAC Direct LED

indicator code

Condition

LED Indicator off

Indicates that the laptop or tablet is unplugged.

LCD panel

The LCD panel provides system information, status, and error messages to indicate if the system is functioning correctly or
requires attention. The LCD panel is used to configure or view the iDRAC IP address of the system. For information about the
event and error messages generated by the system firmware and agents that monitor system components, go to

>

Look Up

>

Error Code

, type the error code, and then click

Look it up

..

The LCD panel is available only on the optional front bezel. The optional front bezel is hot pluggable.

The status and conditions of the LCD panel are outlined here:

●

The LCD backlight is white during normal operating conditions.

●

If there is an issue, the LCD backlight turns amber and displays an error code followed by descriptive text.

NOTE:

If the system is connected to a power source and an error is detected, the LCD turns amber regardless of

whether the system is powered on or off.

●

When the system powers off and there are no errors, the LCD enters the standby mode after five minutes of inactivity.
Press any button on the LCD to power it on.

●

If the LCD panel stops responding, remove the bezel and reinstall it.

If the problem persists, see

.

●

The LCD backlight remains off if LCD messaging is powered off using the iDRAC utility, the LCD panel, or other tools.

Figure 228. LCD panel features

Table 81. LCD panel features

Item Button or

display

Description

1

Left

Moves the cursor back in one-step increments.

2

Select

Selects the menu item highlighted by the cursor.

3

Right

Moves the cursor forward in one-step increments.

During message scrolling:

●

Press and hold the right button to increase scrolling speed.

●

Release the button to stop.

NOTE:

The display stops scrolling when the button is released. After 45 seconds of inactivity,

the display starts scrolling.

4

LCD display

Displays the system information, status, and error messages or iDRAC IP address.

228

System diagnostics and indicator codes

«
...
226
227
228
229
230
...
»

Содержание E70S















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E70S

Univerge SV8100

Бренд: NEC Страницы: 2

SUPERSERVER 6021F

Бренд: Supermicro Страницы: 116

Бренд: Korenix Страницы: 2

UniServer R2900 G3

Бренд: H3C Страницы: 15

SSG-2029P-ACR24H

Бренд: Supermicro Страницы: 136

Бренд: Xblue Networks Страницы: 42

Бренд: Fibrenetix Страницы: 17

Бренд: DNP Страницы: 93

InterServe 600 Series

Бренд: Intergraph Страницы: 104

SUPERSERVER 5014C-MT

Бренд: Supero Страницы: 112

Бренд: 3onedata Страницы: 3

Бренд: D-Link Страницы: 32

Бренд: D-Link Страницы: 22

DP-313 - Air 802.11b Wireless Print Server

Бренд: D-Link Страницы: 28

Бренд: D-Link Страницы: 64

D DP-301P+ DP-301P+

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 100

AirPlus G DP-G301

Бренд: D-Link Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды