Dell E70S Скачать руководство пользователя страница 230 | Manualshive

Страница: 230 / 238

background image

NIC indicator codes

Each NIC on the back of the system has indicators that provide information about the activity and link status. The activity LED
indicator indicates if data is flowing through the NIC, and the link LED indicator indicates the speed of the connected network.

Figure 229. NIC indicator codes

1. Link LED indicator
2. Activity LED indicator

Table 84. NIC indicator codes

NIC indicator codes

Condition

Link and activity indicators are off.

Indicates that the NIC is not connected to the network.

Link indicator is green, and activity indicator is blinking
green.

Indicates that the NIC is connected to a valid network at its maximum
port speed, and data is being sent or received.

Link indicator is amber, and activity indicator is blinking
green.

Indicates that the NIC is connected to a valid network at less than its
maximum port speed, and data is being sent or received.

Link indicator is green, and activity indicator is off.

Indicates that the NIC is connected to a valid network at its maximum
port speed, and data is not being sent or received.

Link indicator is amber, and activity indicator is off.

Indicates that the NIC is connected to a valid network at less than its
maximum port speed, and data is not being sent or received.

Link indicator is blinking green, and activity is off.

Indicates that the NIC identity is enabled through the NIC
configuration utility.

Power supply unit indicator codes

AC and DC power supply units (PSUs) have an illuminated translucent handle that serves as an indicator. The indicator shows if
power is present or if a power fault has occurred.

Figure 230. AC PSU status indicator

1. AC PSU handle
2. Socket
3. Release latch

230

System diagnostics and indicator codes

«
...
228
229
230
231
232
...
»

Содержание E70S















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E70S

Flex System x440 Compute Node

Бренд: IBM Страницы: 584

Бренд: NEC Страницы: 128

SUPERO SuperServer 1018L-MP

Бренд: Supermicro Страницы: 104

Бренд: Gigabyte Страницы: 115

Бренд: 7thSense Страницы: 28

TVS-72XU Series

Бренд: QNAP Страницы: 53

QuantaGrid D51PH-1ULH

Бренд: QCT Страницы: 167

eserver xSeries 350

Бренд: IBM Страницы: 174

Titan SiliconServer

Бренд: Blue Arc Страницы: 487

ANTMAINER S19j Server

Бренд: BITMAIN Страницы: 21

G4-Apex-ENTERPRISE-HW

Бренд: Viavi Страницы: 8

Бренд: Gigabyte Страницы: 152

Бренд: Vision Hi-Tech Страницы: 2

ProxyServer MTPSR1-202ST

Бренд: Multitech Страницы: 142

Бренд: Xerox Страницы: 2

Бренд: QNAP Страницы: 16

Бренд: Kantech Страницы: 114

Бренд: Lantronix Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды