Dell E70S Скачать руководство пользователя страница 225

Страница: 225 / 238

System diagnostics and indicator codes

This section describes the diagnostic indicators on the system front panel that displays the system status during system startup.

Topics:

•

Status LED indicators

•

System health and system ID indicator codes

•

iDRAC Quick Sync 2 indicator codes

•

iDRAC Direct LED indicator codes

•

LCD panel

•

NIC indicator codes

•

Power supply unit indicator codes

•

Drive indicator codes

•

Using system diagnostics

Status LED indicators

NOTE:

The indicators display solid amber if any error occurs.

Figure 226. Status LED indicators

Table 77. Status LED indicators and descriptions

Icon

Description

Condition

Corrective action

Drive indicator

The indicator turns solid amber if
there is a drive error.

●

Check the System Event Log to determine if the
drive has an error.

●

Run the appropriate Online Diagnostics test.
Restart the system and run embedded
diagnostics (ePSA).

●

If the drives are configured in a RAID array,
restart the system, and enter the host adapter
configuration utility program.

Temperature
indicator

The indicator turns solid amber if
the system experiences a thermal
error (for example, the ambient
temperature is out of range or
there is a fan failure).

Ensure that none of the following conditions exist:

●

A cooling fan has been removed or has failed.

●

System cover, air shrouds, or back filler bracket
has been removed.

●

Ambient temperature is too high.

●

External airflow is obstructed.

If the problem persists, see the

Getting help

section.

System diagnostics and indicator codes

225

Содержание E70S















































































































































































































































Результаты поиска

Содержание E70S

Отзывы:

Похожие инструкции для E70S

Бренды по названию

Популярные бренды

Dell E70S, Инструкция по установке и обслуживанию

Результаты поиска

Содержание E70S

Отзывы:

Похожие инструкции для E70S

Бренды по названию

Популярные бренды