Dell E70S Скачать руководство пользователя страница 149

Страница: 149 / 238

Figure 138. Installing the Riser 4 blank

Next steps

Replace the expansion card riser

Installing the expansion card risers

Prerequisites

1. Follow the safety guidelines listed in the

Safety instructions

2. Follow the procedure listed in

Before working inside your system

3. If removed,

install the expansion cards into the expansion card risers

NOTE:

Install Riser 2 before installing Riser 1 and Riser 3. Install Riser 4 after installing Riser 3.

CAUTION:

Do not install GPUs, network cards, or other PCIe devices on your system that are not validated

and tested by Dell. Damage caused by unauthorized and invalidated hardware installation will null and void the
system warranty.

Steps

1. If installed, remove the riser blanks and if required loosen the captive screws.

NOTE:

Store the riser blanks for future use. Filler brackets must be installed in empty expansion card slots to maintain

Federal Communications Commission (FCC) certification of the system. The brackets also keep dust and dirt out of the
system and aid in proper cooling and airflow inside the system

Installing and removing system components

149

Содержание E70S















































































































































































































































Результаты поиска

Содержание E70S

Отзывы:

Похожие инструкции для E70S

Бренды по названию

Популярные бренды

Dell E70S, Инструкция по установке и обслуживанию

Результаты поиска

Содержание E70S

Отзывы:

Похожие инструкции для E70S

Бренды по названию

Популярные бренды