Dell E70S Скачать руководство пользователя страница 155

Страница: 155 / 238

Figure 148. Installing the filler bracket

Next steps

1. If applicable,

install an expansion card into the expansion card riser

Installing an expansion card into the expansion card riser

Prerequisites

1. Follow the safety guidelines listed in the

Safety instructions

2. Follow the procedure listed in

Before working inside your system

3. If installing a new expansion card, unpack it and prepare the card for installation.

NOTE:

For instructions, see the documentation accompanying the card.

CAUTION:

Do not install GPUs, network cards, or other PCIe devices on your system that are not validated

and tested by Dell. Damage caused by unauthorized and invalidated hardware installation will null and void the
system warranty.

Steps

1. Pull and lift up the expansion card retention latch lock to open.
2. If installed, remove the filler bracket.

NOTE:

Store the filler bracket for future use. Filler brackets must be installed in empty expansion card slots to maintain

Federal Communications Commission (FCC) certification of the system. The brackets also keep dust and dirt out of the
system and aid in proper cooling and airflow inside the system.

Installing and removing system components

155

Содержание E70S















































































































































































































































Результаты поиска

Содержание E70S

Отзывы:

Похожие инструкции для E70S

Бренды по названию

Популярные бренды

Dell E70S, Инструкция по установке и обслуживанию

Результаты поиска

Содержание E70S

Отзывы:

Похожие инструкции для E70S

Бренды по названию

Популярные бренды