DEL PowerVault 124T DLT VS160 Скачать руководство пользователя

Страница: 57 / 79

Troubleshooting: Dell PowerVault 124T DLT VS160 Autoloader User's Guide

file:///T|/htdocs/stor-sys/124T/en/124tvs16/trouble.htm[12/5/2012 10:26:08 AM]

Mail Slot Solenoid Error

Insert a cartridge into the autoloader through the mail slot. Verify the

cartridge is sensed and the door closes fully.

If all previous steps fail, contact

support.dell.com

Servo Initialization Error

Remove and inspect the magazines one at a time. Turn the white

thumbwheels on each magazine and insure that the carriers move freely at

least one full rotation in each direction. Re-insert each magazine after

inspection.

Check the barcode reader setting through either the Remote Management

Unit or the Operator Control Panel.

If the barcode reader is enabled, verify that all cartridges have valid

barcode labels. If cartridges do not have valid barcode labels, disable the

barcode reader.

Check

support.dell.com

for PowerVault 124T firmware updates.

Power cycle the autoloader.

Run the Random Moves test from either the Remote Management Unit

(RMU) or the Operator Control Panel (OCP).

Note: The Random Moves test requires a minimum of two cartridges

present within the autoloader.

If all previous steps fail, contact

support.dell.com

Error Log Information

Event

Used to analyze start of servo/motor error sequence in the Soft Error Log. Error

entries immediately following indicate nature of specific motor/position error.

No action required.

Servo Picker Hardware Error Types

Rotation Sensor Bad

Power cycle the autoloader.

Run the Random Moves test from either the Remote Management Unit

(RMU) or the Operator Control Panel (OCP).

Note: The Random Moves test requires a minimum of two cartridges

present within the autoloader.

If all previous steps fail, contact

support.dell.com

Rotation Flag Not Found

Rotation Flag Bad

Translation Sensor Bad

Translation Sensor 1 Bad

Translation Sensor 2 Bad

Translation Flag Bad

Rotational Calibration Lost

Translation Calibration Lost

Rotation Lost

Translation Lost

Rotation Position Lost

Translation Position Lost

Picker Dropped Cartridge

Error

Check for a jammed cartridge in the picker. Remove the cartridge if

present.

Remove and inspect the magazines one at a time. Turn the white

thumbwheels on each magazine and insure that the carriers move freely at

least one full rotation in each direction.

Fully insert a cartridge into each magazine slot, then remove. Look for

Picker Missed Cartridge

Error

Picker Jammed Cartridge

Error

Содержание PowerVault 124T DLT VS160
















































































Результаты поиска

Содержание PowerVault 124T DLT VS160

Отзывы:

Похожие инструкции для PowerVault 124T DLT VS160

Бренды по названию

Популярные бренды

DEL PowerVault 124T DLT VS160, Руководство пользователя

Результаты поиска

Содержание PowerVault 124T DLT VS160

Отзывы:

Похожие инструкции для PowerVault 124T DLT VS160

Бренды по названию

Популярные бренды