DEL PowerVault 124T DLT VS160 Скачать руководство пользователя

Страница: 13 / 79

Installing the Autoloader: Dell PowerVault 124T DLT VS160 Autoloader User's Guide

file:///T|/htdocs/stor-sys/124T/en/124tvs16/install.html[12/5/2012 10:25:55 AM]

8. When the scan is complete, verify the LUN device has been detected using the

list storage adapters

command.

Typical output with both the tape drive and loader being recognized:

0x08 [V321 -A3] Adaptec SCSI Card 39160/3960D – Ultra160 SCSI [slot  201]
  0x16 [V321 -A3-D5:1]  DELL PV-124T 0031
  0x15 [V321 -A3-D5:0]  CERTANCE ULTRIUM 2 1775
0x09 [V321 -A4] Adaptec SCSI Card 39160/3960D – Ultra160 SCSI [slot  202]

Netware may display

unbound device

, meaning a driver is not bound to the loader unless a driver from a backup

software is loaded. This does not prevent the backup application from detecting the LUN and binding the appropriate

driver.

NOTE:

The user must type the command

scan all

upon OS boot every time. If backup software services automatically

start on OS boot, the user must disable them, run the

scan all

command, and re-enable the services.

NOTE:

Netware may display

unbound device

meaning a driver is not bound to the loader unless a driver from a

backup software is loaded. This does not prevent the backup application from detecting the LUN and binding the

appropriate driver.

Back to Contents Page

Содержание PowerVault 124T DLT VS160
















































































Результаты поиска

Содержание PowerVault 124T DLT VS160

Отзывы:

Похожие инструкции для PowerVault 124T DLT VS160

Бренды по названию

Популярные бренды

DEL PowerVault 124T DLT VS160, Руководство пользователя

Результаты поиска

Содержание PowerVault 124T DLT VS160

Отзывы:

Похожие инструкции для PowerVault 124T DLT VS160

Бренды по названию

Популярные бренды