Del ozone TrioPure-25, Инструкция по установке и эксплуатации

Страница: 12 / 26

30,000 32,500 35,000 37,500 40,000 42,500 45,000 47,500 50,000
0
876 949 1,022 1,095 1,168 1,241 1,314 1,388 1,461
250 814 882 949 1,017 1,085 1,153 1,221 1,288 1,356
500 751 814 876 939 1,002 1,064 1,127 1,189 1,252
750 689 746 803 861 918 975 1,033 1,090 1,148
1000 626 678 730 782 835 887 939 991 1,043
1250 563 610 657 704 751 798 845 892 939
1500 501 542 584 626 668 709 751 793 835
1750 438 475 511 548 584 621 657 694 730
2000
376 407 438 469 501 532 563 595 626
2250
313 339 365 391 417 443 469 496 522
2500
250 271 292 313 334 355 376 396 417
2750
188 203 219 235 250 266 282 297 313
3000 125 136 146 156 167 177 188 198 209
3250 63 68 73 78 83 89 94 99 104
3500 0 0 0 0 0 0 0 0 0
Over
5000
Dilute Dilute Dilute Dilute Dilute Dilute Dilute Dilute Dilute
Volume in Gallons (30,000 to 50,000)
Current
Salt Level
[ppm]
3H When to Add Salt and Stabilizer
Step 1 -
Determine the size of your pool in gallons. Please see
Section 3F.
Step 2 -
Check the salinity of the pool water. Always use a salinity
test strip or electronic salinity meter to determine the salt level
in the pool water prior to adding any salt. Check stabilizer level
prior to adding cyanuric acid.
Step 3 -
Use the
Salt Sizing Table
(Section 3G) to determine how
much salt you will need. If existing stabilizer levels require it, you
may also need to add about 1.25 pounds of stabilizer (Cyanuric
Acid) for every 50 pounds of salt added to the pool. For example,
if adding 750 pounds, the quantity of stabilizer needed would
equal 750 pounds / 50 pounds X 1.25 = 18 ¾ pounds.
Note:
To add Cyanuric Acid, slowly sprinkle into the skimmer.
Step 4 -
Turn on the main pool pump with suction coming from
the main pool drain.
Step 5 -
Add salt directly to the pool
[DO NOT add to the skim-
mer box]
by dispersing it around the outside edge of the pool.
Step 6 - Use a pool brush to mix and help dissolve the salt. Keep
the main pump running for 24 hours.
Step 7 - Check the pool salinity. If the salt level is much lower or
higher than expected, first re-check your calculations for adding
salt. Second, check the pool for any undissolved salt and con-
tinue to brush and run the main pump as needed.
REMINDER:
Even if the salt concentration is higher than 3,000 ppm, the
‘Low Salt’ light may flash if the water temperature is at the low
end of the specified range or the Chlorine Control knob is at a
low setting (1-4 shown on the LED display). This is especially
true during the initial preparation and start-up. In this situation,
the TrioPure ™ may not display “10” at the maximum setting.
9
TrioPure
TM
Sanitation System
3G Salt Sizing Table (Continued)
DEL Ozone · San Luis Obispo, CA 93401 · USA · 800-676-1335 · Fax: 805-541-8459
Figure 7, Cont.