Del ozone TrioPure-25, Инструкция по установке и эксплуатации

Страница: 5 / 26

•
The TrioPure ™ has been designed with an electronic water
flow switch. This device automatically shuts down the pump,
salt chlorinator and ozone subsystems when the water flow
through the TrioPure ™ is interrupted. To prevent personal
injury and damage to the TrioPure ™ salt chlorinator cell, do
not interfere with this system in any way. It is designed for
your protection and the protection of the TrioPure ™ .
• •
Pool water with high calcium levels, or hard water,
can cause excessive calcification [scale] in the
Chlorinator Cell. Installation of a T-filter or Y-filter
trap with a 60-mesh screen near the Water Out line
of the TrioPure
™
, along with frequent acid cleaning
of the cell plates [reference Section 5d-1: Chlorina-
tor Cell Plate Cleaning] will reduce water hardness
over time. The monthly addition of a non-chlorine
shock (Potassium Monopersulfate or equivalent) to
the pool will keep the scale soft, preventing the filter
trap from clogging. Remove and clean the filter trap
as necessary.
2
2A Verify Contents
Inspect your TrioPure ™ shipping box for the following items:
(1) TrioPure ™ -25 or TrioPure ™ -50 with salt chlorinator cell
attached
(1) Bypass manifold and return “T” fitting
(1) 3.0A fuse for 120V & (1) 1.5A fuse for 240V
(1) Manual
(1) Quick Reference Guide
(1) Cleaning Kit
(1) Slip - Fit mating unions for The TrioPure
™ water in and
out lines
2B Installation Tips
CAUTION: The bypass manifold must be correctly installed
or your TrioPure
TM
system will not work properly and the war-
ranty will be voided. The bypass manifold contains two check
valves that are matched to create the correct backpressure and
anti-siphon protection for optimum performance of your The
TrioPure ™ at most flow rates.
• •
•
Do not plumb the TrioPure ™ upstream of an in-floor cleaning
system (ICS). Instead, use a dedicated return or alternate
line back to the pool.
• •
•
For installations with solar heating systems, do not plumb so
that water from the TrioPure ™ can go into the solar heater.
Also, air bubbles from the solar return must not be allowed
into the TrioPure ™ inlet line. Either install the bypass mani-
fold upstream of the solar system inlet or use a check valve
in the solar return line with enough restriction to hold air in.
See Figure 1.
• •
•
DO NOT USE
copper or iron piping for the TrioPure
™
installa-
tion as chlorine and ozone have corrosive effects. Consult
your pool professional for appropriate pool equipment piping
materials.
• •
Even though the TrioPure ™ is designed for outdoor use,
care should be taken when choosing a mounting location.
To protect your investment, mount the TrioPure
TM
where
it is protected from the elements (i.e., direct sun, rain,
dirt, sprinklers) and completely sheltered, if possible,
while providing adequate ventilation.
• •
•
Plumb the TrioPure ™ to the bypass manifold using a minimum
amount of plumbing fittings. This minimizes backpressure
and maximizes ozone injector performance. (Recommended
1½” dedicated pool return.)
SECTION 2 Installation
The most common pool and pool/spa configurations are
discussed in this manual. For questions on your specific
installation, please contact DEL Ozone at 800-676-1335,
extension 293.
TrioPure
TM
Sanitation System
DEL Ozone · San Luis Obispo, CA 93401 · USA · 800-676-1335 · Fax: 805-541-8459
2C Recommended Installation
Materials
•
Liquid tight conduit, connectors & junction box,
and appropriately sized and rated wire per local
electrical codes
Note: The TrioPure ™ is designed for 1/2” NPT
liquid tight fittings
•
Two 2” inch unions for manifold installation to
pool return line (use reducer bushings for 1½”)
•
3/4 inch unions, ball-valves, and rigid PVC or Spa-
Flex flex tubing for installation from manifold to
TrioPure ™ (recommended 1 1/2” dedicated pool
return line)
•
Mounting hardware for securing TrioPure ™ to a
stable surface (wall, fence, post with backboard)
sufficient to support the unit
Note: If you are mounting the TrioPure ™ to the
side of house wall that is located near a bedroom,
consider using a vibration dampening material to
reduce vibration noise