DAV DA1000V Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 40

DAV DA1000V Скачать руководство пользователя страница 4

3 SAFETY PRECAUTION

Precautions against electric shock

1. This equipment is kept under high pressure for a while even after the main power supply is cut off. When performing a wiring
work or inspection that touches all terminals of the terminal block, leave it for at least five minutes after shutting off the power
before you start the work.
2. To prevent electric shock and malfunction, please provide class 3 grounding.
(100Ω or less, wire diameter 1.6mm or thicker)
3. Inspection and maintenance of this equipment must be performed by a qualified technician(specialist).
4. Do not inspect equipment with wet hands, when the floor is wet or if there is too much moisture. It may cause electric shock.
5. Be careful not to damage the cable, place heavy objects on it or fold it. In case it is damaged, it may cause electric shock.

Precautions against Fire

1. Do not install this equipment near inflammables, combustible organic solvents or vapors. The heat and electrical operation can
cause fire.
2. If this equipment malfunctions, disconnect the main power supply of the equipment. The high current may cause a fire.

Precautions on Wiring

1. Before conducting wiring work for maintenance etc., be sure to shut off all the external power supplies used by the equipment.
Failure to do so may result in electric shock or damage to the equipment.
2. To supply power or operate the equipment after wiring, be sure to attach the covers inside and outside the equipment. Failure to
do so may result in infury and electric shock.

1. Do not apply main power supply except for that of the voltage specified in this user manual. It may cause malfunction.
2. Make sure that terminal connections and wiring are correct. It may cause malfunction.
3. While the electric current is being applied, do not change the wiring or detach the connector. It may cause injury or equipment
failure.
4. If the power wiring in the driving area is wrong, it may cause injury or damage to the equipment due to malfunction. Be careful.

DANGER

CAUTION

Installation and maintenance guide

THE SAFETY PRECAUTIONS HAVE BEEN CLASSIFIED INTO “DANGER” AND “CAUTION”.

“DANGER” means that dangerous situations can occur and death or serious injury could result, if handled incorrectly.

“CAUTION” means that dangerous situations can occur if handled incorrectly. Also you may get serious injury or

physical damage.

In addition, even if it is indicated as caution, it may lead to serious consequences depending on the situation. Since this is

important for the safety of the user, please make sure you follow the instructions.

!

!

«
...
2
3
4
5
6
...
»

Содержание DA1000V









































Отзывы:

Нет отзывов