
pag
. 31
DA1000V VOLUMETRIC MANUAL DISPENSING SYSTEM
Figure 28. STEADY MODE SETTING PAGE
8.4.2 STEADY MODE
CATEGORY
Sets the dispensing SPEED RATE
> The % can be input using the buttons, increasing or decreasing the % with
the left and right buttons.
This is the PAGE to configure the elements required for STEADY MODE.
Sets the number of SUCKBACK steps
> If the number of SUCKBACK steps is set, the suckback time will be deter-
mined and displayed based on the set DA 1000V capacity.
When the dispensing signal is ON in STEADY MODE, the DA 1000V will wait
until the duration specified in ON DELAY before commencing the dispensing.
MAX (cc/sec) > Displays the maximum speed of the DA 1000V based on the
set Barrel capacity
SV (cc/sec) > Displays the set TIME and VOLUME as speed values.
DESCRIPTION
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
38/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 28. STEADY MODE SETTING PAGE
This is the PAGE to configure the elements required for STEADY MODE.
Category
Description
Sets the dispensing SPEED RATE
→
The % can be input using the buttons, increasing or
decreasing the % with the left and right buttons.
Sets the number of SUCKBACK steps
→
If the number of SUCKBACK steps is set, the suckback
time will be determined and displayed based on the set Nano
Pen capacity.
When the dispensing signal is ON in STEADY MODE, the
Nano Pen will wait until the duration specified in ON DELAY
before commencing the dispensing.
MAX (cc/sec) →
Displays the maximum speed of the Nano
Pen based on the set Barrel capacity
SV (cc/sec) → Displays the set TIME and VOLUME as speed
values
7.4.3
INTERVAL MODE
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
38/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 28. STEADY MODE SETTING PAGE
This is the PAGE to configure the elements required for STEADY MODE.
Category
Description
Sets the dispensing SPEED RATE
→
The % can be input using the buttons, increasing or
decreasing the % with the left and right buttons.
Sets the number of SUCKBACK steps
→
If the number of SUCKBACK steps is set, the suckback
time will be determined and displayed based on the set Nano
Pen capacity.
When the dispensing signal is ON in STEADY MODE, the
Nano Pen will wait until the duration specified in ON DELAY
before commencing the dispensing.
MAX (cc/sec) →
Displays the maximum speed of the Nano
Pen based on the set Barrel capacity
SV (cc/sec) → Displays the set TIME and VOLUME as speed
values
7.4.3
INTERVAL MODE
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
38/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 28. STEADY MODE SETTING PAGE
This is the PAGE to configure the elements required for STEADY MODE.
Category
Description
Sets the dispensing SPEED RATE
→
The % can be input using the buttons, increasing or
decreasing the % with the left and right buttons.
Sets the number of SUCKBACK steps
→
If the number of SUCKBACK steps is set, the suckback
time will be determined and displayed based on the set Nano
Pen capacity.
When the dispensing signal is ON in STEADY MODE, the
Nano Pen will wait until the duration specified in ON DELAY
before commencing the dispensing.
MAX (cc/sec) →
Displays the maximum speed of the Nano
Pen based on the set Barrel capacity
SV (cc/sec) → Displays the set TIME and VOLUME as speed
values
7.4.3
INTERVAL MODE
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
38/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 28. STEADY MODE SETTING PAGE
This is the PAGE to configure the elements required for STEADY MODE.
Category
Description
Sets the dispensing SPEED RATE
→
The % can be input using the buttons, increasing or
decreasing the % with the left and right buttons.
Sets the number of SUCKBACK steps
→
If the number of SUCKBACK steps is set, the suckback
time will be determined and displayed based on the set Nano
Pen capacity.
When the dispensing signal is ON in STEADY MODE, the
Nano Pen will wait until the duration specified in ON DELAY
before commencing the dispensing.
MAX (cc/sec) →
Displays the maximum speed of the Nano
Pen based on the set Barrel capacity
SV (cc/sec) → Displays the set TIME and VOLUME as speed
values
7.4.3
INTERVAL MODE
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
38/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 28. STEADY MODE SETTING PAGE
This is the PAGE to configure the elements required for STEADY MODE.
Category
Description
Sets the dispensing SPEED RATE
→
The % can be input using the buttons, increasing or
decreasing the % with the left and right buttons.
Sets the number of SUCKBACK steps
→
If the number of SUCKBACK steps is set, the suckback
time will be determined and displayed based on the set Nano
Pen capacity.
When the dispensing signal is ON in STEADY MODE, the
Nano Pen will wait until the duration specified in ON DELAY
before commencing the dispensing.
MAX (cc/sec) →
Displays the maximum speed of the Nano
Pen based on the set Barrel capacity
SV (cc/sec) → Displays the set TIME and VOLUME as speed
values
7.4.3
INTERVAL MODE