
pag
. 11
DA1000V VOLUMETRIC MANUAL DISPENSING SYSTEM
Name and Display
Function and Description
This is the grounding connector for the power for the
DA 1000V Controller.
<Frame Ground>
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
16/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
<Frame Ground>
This is the grounding connector for the power for
the NPC-10.
<DC Receptacle>
This can be connected through the Power
Adaptor.
<Nano Pen Connector>
This is the Connector that connects to the Nano
Pen Cable.
<FOOT Connector>
This is the Connector that is connected in order
to operate the Nano Pen FOOT Switch.
This is a D-SUB 9-pin Connector, which allows
Firmware Updates as well as 485 communication.
This is the Pin Map used when executing
Controller Firmware Updates.
2: Rx232
3: Tx232
5: GND
9: BOOT
This is the Pin Map used for 485 communication.
6: RS485+
7: RS485
−
This is a D-SUB 9-pin Connector, which allows Firmware
Updates as well as 485 communication.
This is the Pin Map used when executing Controller
Firmware Updates.
2: Rx232
3: Tx232
5: GND
9: BOOT
This is the Pin Map used for 485 communication.
6: RS485+
7: RS485
<POWER Switch>
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
16/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
<Frame Ground>
This is the grounding connector for the power for
the NPC-10.
<DC Receptacle>
This can be connected through the Power
Adaptor.
<Nano Pen Connector>
This is the Connector that connects to the Nano
Pen Cable.
<FOOT Connector>
This is the Connector that is connected in order
to operate the Nano Pen FOOT Switch.
This is a D-SUB 9-pin Connector, which allows
Firmware Updates as well as 485 communication.
This is the Pin Map used when executing
Controller Firmware Updates.
2: Rx232
3: Tx232
5: GND
9: BOOT
This is the Pin Map used for 485 communication.
6: RS485+
7: RS485
−
This is the Connector that is connected in
order to operate the DA 1000V FOOT Switch.
<FOOT Connector>
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
16/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
<Frame Ground>
This is the grounding connector for the power for
the NPC-10.
<DC Receptacle>
This can be connected through the Power
Adaptor.
<Nano Pen Connector>
This is the Connector that connects to the Nano
Pen Cable.
<FOOT Connector>
This is the Connector that is connected in order
to operate the Nano Pen FOOT Switch.
This is a D-SUB 9-pin Connector, which allows
Firmware Updates as well as 485 communication.
This is the Pin Map used when executing
Controller Firmware Updates.
2: Rx232
3: Tx232
5: GND
9: BOOT
This is the Pin Map used for 485 communication.
6: RS485+
7: RS485
−
This is the Connector that connects to the DA 1000V
Cable.
<DA 1000V Connector>
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
16/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
<Frame Ground>
This is the grounding connector for the power for
the NPC-10.
<DC Receptacle>
This can be connected through the Power
Adaptor.
<Nano Pen Connector>
This is the Connector that connects to the Nano
Pen Cable.
<FOOT Connector>
This is the Connector that is connected in order
to operate the Nano Pen FOOT Switch.
This is a D-SUB 9-pin Connector, which allows
Firmware Updates as well as 485 communication.
This is the Pin Map used when executing
Controller Firmware Updates.
2: Rx232
3: Tx232
5: GND
9: BOOT
This is the Pin Map used for 485 communication.
6: RS485+
7: RS485
−
This can be connected through the Power
Adaptor.
<DC Receptacle>
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
16/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
<Frame Ground>
This is the grounding connector for the power for
the NPC-10.
<DC Receptacle>
This can be connected through the Power
Adaptor.
<Nano Pen Connector>
This is the Connector that connects to the Nano
Pen Cable.
<FOOT Connector>
This is the Connector that is connected in order
to operate the Nano Pen FOOT Switch.
This is a D-SUB 9-pin Connector, which allows
Firmware Updates as well as 485 communication.
This is the Pin Map used when executing
Controller Firmware Updates.
2: Rx232
3: Tx232
5: GND
9: BOOT
This is the Pin Map used for 485 communication.
6: RS485+
7: RS485
−