
Installation and maintenance guide
Figure 29. INTERVAL MODE SETTING PAGE
8.4.3 INTERVAL MODE
CATEGORY
Sets the dispensing duration
Sets the dispensing volume
Shows the wait time after one dispensing operation until the next
Sets the number of SUCKBACK steps
> If the number of SUCKBACK steps is set, the suckback time will be deter-
mined and displayed based on the set DA 1000V capacity.
The dispensing operation will be repeated based on the set dispensing condi-
tions for the number of CYCLEs indicated.
When the dispensing signal is ON in INTERVAL MODE, the DA 1000V will wait
until the duration specified in ON DELAY before commencing the dispensing.
The INTERVAL MODE SETTING PAGE is the PAGE to configure the repeated dispensing conditions.
MAX (cc/sec) > Displays the maximum speed of the DA 1000V based on the
set Barrel capacity
SV (cc/sec) > Displays the set TIME and VOLUME as speed values
MIN (sec) > Displays the minimum number of seconds that can be changed
based on the set VOLUME
MAX (cc) > Displays the maximum VOLUME that can be changed based on
the set TIME
DESCRIPTION
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
39/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 29. INTERVAL MODE SETTING PAGE
The INTERVAL MODE SETTING PAGE is the PAGE to configure the repeated dispensing conditions.
Category
Description
Sets the dispensing duration
Sets the dispensing volume
Shows the wait time after one dispensing operation until
the next
Sets the number of SUCKBACK steps
→
If the number of SUCKBACK steps is set, the suckback
time will be determined and displayed based on the set Nano
Pen capacity.
The dispensing operation will be repeated based on the
set dispensing conditions for the number of CYCLEs indicated.
When the dispensing signal is ON in INTERVAL MODE, the
Nano Pen will wait until the duration specified in ON DELAY
before commencing the dispensing.
MAX (cc/sec) → Displays the maximum speed of the Nano
Pen based on the set Barrel capacity
SV (cc/sec)
→ Displays the set TIME and VOLUME as speed
values
MIN (sec) → Displays the minimum number of seconds that
can be changed based on the set VOLUME
MAX (cc) → Displays the maximum VOLUME that can be
changed based on the set TIME
7.4.4
SEQUENCE MODE
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
39/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 29. INTERVAL MODE SETTING PAGE
The INTERVAL MODE SETTING PAGE is the PAGE to configure the repeated dispensing conditions.
Category
Description
Sets the dispensing duration
Sets the dispensing volume
Shows the wait time after one dispensing operation until
the next
Sets the number of SUCKBACK steps
→
If the number of SUCKBACK steps is set, the suckback
time will be determined and displayed based on the set Nano
Pen capacity.
The dispensing operation will be repeated based on the
set dispensing conditions for the number of CYCLEs indicated.
When the dispensing signal is ON in INTERVAL MODE, the
Nano Pen will wait until the duration specified in ON DELAY
before commencing the dispensing.
MAX (cc/sec) → Displays the maximum speed of the Nano
Pen based on the set Barrel capacity
SV (cc/sec)
→ Displays the set TIME and VOLUME as speed
values
MIN (sec) → Displays the minimum number of seconds that
can be changed based on the set VOLUME
MAX (cc) → Displays the maximum VOLUME that can be
changed based on the set TIME
7.4.4
SEQUENCE MODE
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
39/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 29. INTERVAL MODE SETTING PAGE
The INTERVAL MODE SETTING PAGE is the PAGE to configure the repeated dispensing conditions.
Category
Description
Sets the dispensing duration
Sets the dispensing volume
Shows the wait time after one dispensing operation until
the next
Sets the number of SUCKBACK steps
→
If the number of SUCKBACK steps is set, the suckback
time will be determined and displayed based on the set Nano
Pen capacity.
The dispensing operation will be repeated based on the
set dispensing conditions for the number of CYCLEs indicated.
When the dispensing signal is ON in INTERVAL MODE, the
Nano Pen will wait until the duration specified in ON DELAY
before commencing the dispensing.
MAX (cc/sec) → Displays the maximum speed of the Nano
Pen based on the set Barrel capacity
SV (cc/sec)
→ Displays the set TIME and VOLUME as speed
values
MIN (sec) → Displays the minimum number of seconds that
can be changed based on the set VOLUME
MAX (cc) → Displays the maximum VOLUME that can be
changed based on the set TIME
7.4.4
SEQUENCE MODE
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
39/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 29. INTERVAL MODE SETTING PAGE
The INTERVAL MODE SETTING PAGE is the PAGE to configure the repeated dispensing conditions.
Category
Description
Sets the dispensing duration
Sets the dispensing volume
Shows the wait time after one dispensing operation until
the next
Sets the number of SUCKBACK steps
→
If the number of SUCKBACK steps is set, the suckback
time will be determined and displayed based on the set Nano
Pen capacity.
The dispensing operation will be repeated based on the
set dispensing conditions for the number of CYCLEs indicated.
When the dispensing signal is ON in INTERVAL MODE, the
Nano Pen will wait until the duration specified in ON DELAY
before commencing the dispensing.
MAX (cc/sec) → Displays the maximum speed of the Nano
Pen based on the set Barrel capacity
SV (cc/sec)
→ Displays the set TIME and VOLUME as speed
values
MIN (sec) → Displays the minimum number of seconds that
can be changed based on the set VOLUME
MAX (cc) → Displays the maximum VOLUME that can be
changed based on the set TIME
7.4.4
SEQUENCE MODE
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
39/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 29. INTERVAL MODE SETTING PAGE
The INTERVAL MODE SETTING PAGE is the PAGE to configure the repeated dispensing conditions.
Category
Description
Sets the dispensing duration
Sets the dispensing volume
Shows the wait time after one dispensing operation until
the next
Sets the number of SUCKBACK steps
→
If the number of SUCKBACK steps is set, the suckback
time will be determined and displayed based on the set Nano
Pen capacity.
The dispensing operation will be repeated based on the
set dispensing conditions for the number of CYCLEs indicated.
When the dispensing signal is ON in INTERVAL MODE, the
Nano Pen will wait until the duration specified in ON DELAY
before commencing the dispensing.
MAX (cc/sec) → Displays the maximum speed of the Nano
Pen based on the set Barrel capacity
SV (cc/sec)
→ Displays the set TIME and VOLUME as speed
values
MIN (sec) → Displays the minimum number of seconds that
can be changed based on the set VOLUME
MAX (cc) → Displays the maximum VOLUME that can be
changed based on the set TIME
7.4.4
SEQUENCE MODE
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
39/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 29. INTERVAL MODE SETTING PAGE
The INTERVAL MODE SETTING PAGE is the PAGE to configure the repeated dispensing conditions.
Category
Description
Sets the dispensing duration
Sets the dispensing volume
Shows the wait time after one dispensing operation until
the next
Sets the number of SUCKBACK steps
→
If the number of SUCKBACK steps is set, the suckback
time will be determined and displayed based on the set Nano
Pen capacity.
The dispensing operation will be repeated based on the
set dispensing conditions for the number of CYCLEs indicated.
When the dispensing signal is ON in INTERVAL MODE, the
Nano Pen will wait until the duration specified in ON DELAY
before commencing the dispensing.
MAX (cc/sec) → Displays the maximum speed of the Nano
Pen based on the set Barrel capacity
SV (cc/sec)
→ Displays the set TIME and VOLUME as speed
values
MIN (sec) → Displays the minimum number of seconds that
can be changed based on the set VOLUME
MAX (cc) → Displays the maximum VOLUME that can be
changed based on the set TIME
7.4.4
SEQUENCE MODE
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
39/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 29. INTERVAL MODE SETTING PAGE
The INTERVAL MODE SETTING PAGE is the PAGE to configure the repeated dispensing conditions.
Category
Description
Sets the dispensing duration
Sets the dispensing volume
Shows the wait time after one dispensing operation until
the next
Sets the number of SUCKBACK steps
→
If the number of SUCKBACK steps is set, the suckback
time will be determined and displayed based on the set Nano
Pen capacity.
The dispensing operation will be repeated based on the
set dispensing conditions for the number of CYCLEs indicated.
When the dispensing signal is ON in INTERVAL MODE, the
Nano Pen will wait until the duration specified in ON DELAY
before commencing the dispensing.
MAX (cc/sec) → Displays the maximum speed of the Nano
Pen based on the set Barrel capacity
SV (cc/sec)
→ Displays the set TIME and VOLUME as speed
values
MIN (sec) → Displays the minimum number of seconds that
can be changed based on the set VOLUME
MAX (cc) → Displays the maximum VOLUME that can be
changed based on the set TIME
7.4.4
SEQUENCE MODE
NANO PENNANOPEN Operation Manual
Doc. Rev 0
2019/7/2
39/47
Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 29. INTERVAL MODE SETTING PAGE
The INTERVAL MODE SETTING PAGE is the PAGE to configure the repeated dispensing conditions.
Category
Description
Sets the dispensing duration
Sets the dispensing volume
Shows the wait time after one dispensing operation until
the next
Sets the number of SUCKBACK steps
→
If the number of SUCKBACK steps is set, the suckback
time will be determined and displayed based on the set Nano
Pen capacity.
The dispensing operation will be repeated based on the
set dispensing conditions for the number of CYCLEs indicated.
When the dispensing signal is ON in INTERVAL MODE, the
Nano Pen will wait until the duration specified in ON DELAY
before commencing the dispensing.
MAX (cc/sec) → Displays the maximum speed of the Nano
Pen based on the set Barrel capacity
SV (cc/sec)
→ Displays the set TIME and VOLUME as speed
values
MIN (sec) → Displays the minimum number of seconds that
can be changed based on the set VOLUME
MAX (cc) → Displays the maximum VOLUME that can be
changed based on the set TIME
7.4.4
SEQUENCE MODE