Daum electronic Vita 2002 PC de luxe, Руководство пользователя

Страница: 34 / 106

3.
5.
6.
4a
5a
4.
prog
2.
prog
1.
reset
00
)
))
)
))
)
))
watt
30
manual
program
30
IL
IL
IP
IP
Ir
Ir
or or or or
1 x
1 x
1 x
1 x
until window no. 1 displays the
p rog. designation
“IL”
or “
IP”
or “
Ir”
and appears
in window no. 2
The ergo_bike “
vita 2002 pc de luxe”
is equipped with individual training programs IL / IP / Ir. The table below shows
you how to call and program these programs.
Selection and programing of the Individual Programs IL / IP, Ir
These entries can be repeated for a total of 60 minute-steps for user identification numbers “1
to 3”. Individual training profiles of up to 240 minutes can be programmed for user number “4”
the pulse rate prescribed
for the third minute
is displayed
the speed value
in km/h prescribed
for the third minute.
the pulse rate prescribed
for the second minute
is displayed.
the speed value
in km/h prescribed
for the second minute.
displays:
displays:
displays:
evtl. a Prog. No.,
evtl. a Prog. Name
the corresponding
prog. number
the speed value
in km/h prescribed
for the first minute
is displayed when
the selection arrow
is pointing to km/h.
For the Speed
Dependent
Individual Program
displays:
For the Pulse Individual
Program
the pulse rate prescribed
for the first minute
is displayed
Display 5 Display 2
Display 1
Display 4
Display 6
displays:
displays: displays:
e.g.
e.g.
e.g.
Users /
km total
displays:
the selected user number
evtl. a program number
evtl. a program arrow
P
displays:
displays:
P
and the selected
prog. designation
displays:
empty display
if programming
the IL prog. for
the first time or
e.g.
A blinking signal
indicates that the
watt values can
be entered for a
new program
The diagram of
the last individual
IL program
entered
e.g.
This setting
can be modified
in one-minute
step. The bar
corresponding
to the current
minute blinks
to indicate
how the diagram
will be modified
confirm
press
until the arrow in Window No. 4
pointing to Users / km total
appears on the right side
press
displays:
turn
press
E
2
I
0 I
E
2
E
3
etc.
When this program is run, the display follows the same pattern as for normal watt controlled programs.
The graphic display also supports the programming of an individual program: The stored program is
displayed on the screen, with a blinking bar corresponding to the watt value for the current minute that
can be modified by turning the control button. This bar represents the preset watt value for the minute
displayed in window 2. When you press the control button, the next bar starts blinking and can
be changed.
press
press
displays:
The following table shows how to call and program the specific programs.
0
Individual Program P
Training Programs
the
short designation
evtl. a Prog. No.,
evtl. a Prog. Name
the watt load prescribed
for the first minute
is displayed
For the Watt Individual
Program
= Entry
= first minute
of training
Should the displayed value be modified?
Turn the control button No. 6 to set:
The load in watt required for the first training minute of the IL - program
Confirm
the setting
= Entry
= second minute
of training
the watt load
prescribed for
the second minute
is displayed
Should the displayed value be modified?
Turn the control button No. 6 to set:
The load in watt required for the second training minute of the IL - program
Confirm
the setting
the watt load
prescribed for
the third minute
is displayed
= Entry
= third minute
of training
Confirm
the setting
(up to 30
or 240
one minute
steps)
Confirming a setting of
terminates the
programming operation.