Datakom D-500 MK3 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 197

background image

D-500 MK3 User Manual Firmware V-7.5

D-500 MK3

ADVANCED

GENSET

CONTROLLER

D-500 MK3 is a next generation genset controller
combining multi-functionality and wide communication
capabilities together with a reliable and low-cost
design.

The same controller provides synchronization, load
share, AMF, ATS, Remote Start, Engine Control and
Remote Display Panel functionalities.

The module comes ready for remote monitoring over
GSM or Ethernet with plug-in communication modules.

Various plug-in modules provide unlimited expansion
capabilities allowing to meet any special requirement.
The unit complies and mostly exceeds world’s tightest
safety, vibration and environmental standards for the
industrial category.

Software features are complete with easy firmware
upgrade process through USB port.

The Windows based PC software allows monitoring
and programming through USB, RS-485, Ethernet and
GPRS. The Rainbow Scada web monitoring service
allows monitoring and control of an unlimited number
of gensets through any web browser.

Multi genset synchronizer and load share *
Multi genset mains synchronizer *
Single genset parallel with mains *
AMF unit with uninterrupted transfer
ATS unit with uninterrupted transfer
Remote start controller
Manual start controller
Engine controller
Remote display & control unit
Waveform display of V & I
Harmonic analysis of V & I

*

Optional with plug-in module

•

Ethernet port (100Mbps) *

• GSM-GPRS *
• Embedded web server *
• Web monitoring *
• Web programming *
• Central Monitoring through internet *
• SMS message sending *
• E-mail sending *
• Central monitoring *
• Modbus RTU through RS-485 *
• Modbus TCP/IP *
• SNMP *
• USB Host *
• CANBUS-2 for inter- module comm. *
• USB Device
• PC software: Rainbow Plus
• J1939-CANBUS for electronic engines

*

Optional with plug-in module

3 phases 4 wires, star
3 phases 4 wires, delta
3 phases 3 wires, delta, 3 CTs
3 phases 3 wires, delta, 2 CTs (L1-L2)
3 phases 3 wires, delta,2 CTs (L1-L3)
2 phases 3 wires, L1-L2
2 phases 3 wires, L1-L3
1 phase 2 wires

FUNCTIONALITIES

COMMUNICATIONS

TOPOLOGIES

DESCRIPTION

1
2
3
...
»

Содержание D-500 MK3






































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для D-500 MK3

Бренд: Valve Concepts Страницы: 15

Бренд: Lawler Страницы: 5

Бренд: XBOX Страницы: 4

Бренд: Panasonic Страницы: 15

Бренд: Panasonic Страницы: 42

Бренд: KAR-TECH Страницы: 28

Бренд: 2M Technology Страницы: 17

Бренд: 2iB Страницы: 5

Go!Control Panel

Бренд: 2gig Technologies Страницы: 78

Бренд: ZIMO Страницы: 38

Бренд: IAI Страницы: 5

Бренд: Lamtec Страницы: 136

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Olsberg Страницы: 68

Бренд: Sanhua Страницы: 3

Бренд: QED Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды