Datakom D-100 MK2 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 123

background image

D-100 MK2 User Manual Firmware V-6.3

D-100 MK2

ADVANCED

GENSET

CONTROLLER

The D-100 MK2 is a next generation genset control
units combining multi-functionality and wide
communication possibilities together with a reliable
and low cost design.

The unit co

mplies and mostly exceeds world’s

tightest safety, EMC, vibration and environmental
standards for the industrial category.

Software features are complete with easy firmware
upgrade process through USB port.

The Windows based PC software allows monitoring
and programming through USB, serial and GPRS.

The PC based Rainbow Scada software allows
monitoring and control of an unlimited number of
gensets from a single central location.

AMF unit with uninterrupted transfer
ATS unit with uninterrupted transfer
Remote start controller
Manual start controller
Engine controller
CTs at genset or load side

•

GSM Modem (2G-3G-4G) *

•

Ethernet 10/100Mbits *

•

Wi-Fi *

•

RS-485 isolated (2400-38400baud) *

•

RS-232 isolated (2400-38400baud) *

•

USB Device

•

J1939 CANBUS

•

Central Monitoring through internet *

•

SMS message sending *

•

PC software: Rainbow Plus

•

Central monitoring *

•

Modbus RTU through RS-485 *

•

Modbus TCP/IP *

*Optional with plug-in module

3 phases 4 wires, star
3 phases 3 wires, 3 CTs
3 phases 3 wires, 2 CTs (L1-L2)
3 phases 3 wires, 2 CTs (L1-L3)
2 phases 3 wires, L1-L2
2 phases 3 wires, L1-L3
3 phases 4 wires, delta
1 phase 2 wires

FUNCTIONALITIES

COMMUNICATIONS

TOPOLOGIES

DESCRIPTION

1
2
3
...
»

Содержание D-100 MK2




























































































































Отзывы:

Нет отзывов

Похожие инструкции для D-100 MK2

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 146

Бренд: Faber Страницы: 8

Бренд: CAME Страницы: 12

Бренд: CAME Страницы: 16

Бренд: Ultrak Страницы: 41

Бренд: Zander Aachen Страницы: 10

Бренд: CAME Страницы: 32

Бренд: Babybee Prams Страницы: 21

Бренд: Yudian Страницы: 26

Бренд: Zeagle Страницы: 37

Бренд: Jäger Страницы: 50

Бренд: JENCO Страницы: 36

Бренд: jcm-tech Страницы: 8

Бренд: Oceanic Systems Страницы: 8

Бренд: Parker Страницы: 12

Бренд: UniPOS Страницы: 51

Бренд: Unipulse Страницы: 126

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды