Data I/O PSV7000 Скачать руководство пользователя

Страница: 28 / 88

Operation ■ Running a Job on PSV7000

—24—

Data I/O • 096-0461-001G

back

Insert the communication cable part way into the socket on the

handler and, while pushing lightly, rotate until the connector is

oriented correctly (it will stop and make a slight click sound

when it goes the rest of the way on).

The feeder Status lamp should light if the PSV7000 is on.

Install the device reel if it is not already.

Note:

For more information about loading a reel of devices onto the

feeder, see the documentation that came with your tape feeder.

Pull the carrier tape forward to start it into the sprocket wheel.

Then advance the carrier tape, via the tape feeder, into the exit

chute. Refer to previous figures for the tape chute.

The empty device

carrier

tape will come out of the slot below the

mounting latch. If the Take-up Reel option is not used, place a

box on the floor to contain empty carrier tape.

Thread the

cover

tape through the tape window and onto the

feeder’s cover tape roller.

10. Adjust pitch. Count the number of sprocket holes in the carrier

tape between the center of one pocket and the center of the next

pocket. Use this pitch number and follow the instructions for

your particular Tape Feeder to set the pitch index.

Later, after the PSV7000 has been powered up,

remember to align the pick point—

A. On the

Gantry

window, press

Park

B. Advance the carrier tape until the pick point mark on the feeder

aligns with the center of a pocket.

It may be necessary to advance the tape forward one pocket.

Note:

If a Tape Take-up Module is used, install it: see

the next

heading

To remove the Tape
Feeder communication
cable, grasp the collar
and pull out.

For more informa-

tion about threading

carrier tape, see the

documentation that

came with your tape

feeder.

Remember to remove
cover tape from the
cover tape reel when
full. For more informa-
tion, see your Tape
Feeder documentation.

Содержание PSV7000

























































































Результаты поиска

Содержание PSV7000

Отзывы:

Похожие инструкции для PSV7000

Бренды по названию

Популярные бренды

Data I/O PSV7000, Руководство оператора

Результаты поиска

Содержание PSV7000

Отзывы:

Похожие инструкции для PSV7000

Бренды по названию

Популярные бренды