Data I/O PSV7000 Скачать руководство пользователя страница 8

Страница: 8 / 88

■ PSV7000 Machine Components

—4—

Data I/O • 096-0461-001G

back

Programmer Overview

LumenX

LumenX is Data I/O’s latest programmer at the time of this document.

Each LumenX programmer requires one to two Actuator Plates and

one to eight Socket Adapters for the specific device package being

programmed. Each Socket Adapter has one socket.

Figure 4: One LumenX programmer with eight Sockets.

LED Interpretation on LumenX Programmers

Figure 5: Each LumenX Socket Adapter has four LEDs and indicates

PIN 1 as shown. All four LEDs light at once only during startup and go

off when the startup procedure is complete. The Actuator Plate is not

shown here for clarity.

Green = PASS PROGRAMMING

Yellow = BUSY

Red = FAILED PROGRAMMING

White = CONTINUITY ERROR

Jobs for LumenX pro-
grammers are created
with LumenX Data Man-
agement Software.

Actuator Plates

Socket Adapters
(small arrows)

Clamp (4)

Spring Clip (4)

Programmer

Содержание PSV7000

























































































Результаты поиска

Содержание PSV7000

Отзывы:

Бренды по названию

Популярные бренды

Data I/O PSV7000, Руководство оператора

Результаты поиска

Содержание PSV7000

Отзывы:

Бренды по названию

Популярные бренды