Data I/O PSV7000 Скачать руководство пользователя | Manualshive

Страница: 36 / 88

background image

Operation ■ Running a Job on PSV7000

—32—

Data I/O • 096-0461-001G

back

the front of the machine and should contain a 1 M-ohm to
10 M-ohm current limiting resistor.

(FC) Installing Adapters and Actuators

For LumenX see

page 35

.

To install or change a Socket Adapter on a FlashCORE programmer:

1.

If a job is running, click

Finish

on the

Run

window and wait for

the PNP head to empty the sockets, move to the Park position

and stop.

2.

Open the safety door that offers the easiest access to the target

programmer(s).

3.

With sockets closed (actuators up), remove the Actuator Plate by

sliding it out toward the front or back of the machine. Refer to

the figures below.

If the programmer is between two others, one of the adjacent

Actuator Plates must be in the down position (sockets open) for

access.

Figure 16: Remove the Actuator Plate by sliding it out from the bracket

in either direction; sockets must be closed (up position). If the

WARNING:  Pinch hazard! SOCKET ACTUATORS CAN STILL
MOVE UP AND DOWN WHEN THE SAFETY DOORS ARE
OPEN  AND EVEN WHEN THE E-STOP IS PUSHED—the air
does not shut off.

Operation of the machine should be the responsibility of one
operator and all other people should not interact with the con-
trols at the monitor (which can trigger socket actuation).

Installing the Socket
Adapters and Actuator
Plates can be done
later, after setting
media options in the
SETUP Window.

A job can be continued
later—even after clicking

Finish

.

If removing all Actuator
Plates in a row of pro-
grammers, start with the
nearest one, and slide each
plate forward.

(Ending a job leaves the
Actuator Plates up for
quick access.)

«
...
34
35
36
37
38
...
»

Содержание PSV7000

























































































Отзывы:

Нет отзывов

Похожие инструкции для PSV7000

AF-600 FP Series

Бренд: GE Страницы: 7

Бренд: Jafar Страницы: 9

Бренд: Febco Страницы: 4

Бренд: Cisco Страницы: 48

C-NaviGator III

Бренд: C-Nav Страницы: 20

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: halstrup-walcher Страницы: 39

Бренд: Samson Страницы: 20

SHERPA MONOBLOC B0812

Бренд: Olimpia splendid Страницы: 44

Бренд: Olimpia splendid Страницы: 44

Бренд: Olimpia splendid Страницы: 16

Бренд: Water Specialist Страницы: 60

Бренд: Technische Alternative Страницы: 68

Бренд: National Instruments Страницы: 9

Gator Grip Drum EGG-1

Бренд: Wesco Страницы: 2

Бренд: EBS Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды