Data I/O PSV7000 Скачать руководство пользователя

Страница: 78 / 88

Operation ■ Dual Tray Feeder

—74—

Data I/O • 096-0461-001G

back

Dual Tray Feeder

There is an automatic Dual Tray Feeder option available for the

PSV7000 System. Chapter 2 of the Owner’s Manual discusses setting

it up. Operation is discussed here.

Note:

This information is for Dual Tray Feeder Model EX. For

earlier models, refer to the manuals that came with your system.

Operating the Dual Tray Feeder ‘EX’

As an option, the PSV7000 System can be configured with an Dual

Tray Feeder. Only basic operation of the Data I/O Automatic Tray

Feeder is described here.

To start the Dual Tray Feeder EX:
1.

Ensure the Dual Tray Feeder is plugged into the

PSV7000 Machine.

Note:

The Tray Feeder will power up when the PSV7000 Machine

is started.

Prior to clicking

Start

in AH700, install up to 20 JEDEC trays of

unprogrammed devices into the

Input Stack

of the Tray Feeder.

Start a PSV7000 job as usual (through TaskLink or Job Runner).

The Tray Feeder loads the first tray.

In AH700, click

Start

. The Tray Feeder initializes.

The AH700 will display a message when an empty tray is

required at the Empty Tray Position.

At the S

etup > Options

tab select the tray options desired.

When

Setup

options are set, ensure that the machine workspace

matches the settings. Rectify differences.

Click

Run

. (A password may be required.)

For physically setting
up the Tray Feeder on
PSV7000, see Chap-
ter 2 of the

PSV7000

Owner’s Manual

For more information
about operating it,
see the

Dual Tray

Feeder Owner’s
Manual

under the

AH700 Help menu.

Содержание PSV7000

























































































Результаты поиска

Содержание PSV7000

Отзывы:

Похожие инструкции для PSV7000

Бренды по названию

Популярные бренды

Data I/O PSV7000, Руководство оператора

Результаты поиска

Содержание PSV7000

Отзывы:

Похожие инструкции для PSV7000

Бренды по названию

Популярные бренды