manualshive.com logo in svg

Danfoss VLT MCA 121 EtherNet/IP, Руководство пользователя

Поделиться
Скачать
Danfoss VLT MCA 121 EtherNet/IP Скачать руководство пользователя страница 36

12-01  IP Address

Range:

Function:

  [000.000.000.000 -
255.255.255.255]

Configure the IP address of the option. Read-only if par. 12-00 set to DHCP or BOOTP.

12-02  Subnet Mask

Range:

Function:

  [000.000.000.000 -
255.255.255.255]

Configure the IP subnet mask of the option. Read-only if par. 12-00 set to DHCP or BOOTP.

12-03  Default Gateway

Range:

Function:

  [000.000.000.000 –
255.255.255.255]

Configure the IP default gateway of the option. Read-only if par. 12-00 set to DHCP or BOOTP.

12-04  DHCP Server

Range:

Function:

  [000.000.000.000 –
255.255.255.255]

Read only. Displays the IP address of the found DHCP or BOOTP server.

NB!

A power-cycle is necessary after setting the IP parameters manually.

12-05  Lease Expires

Range:

Function:

  [dd:hh:mm:ss]

Read only. Displays the lease-time left for the current DHCP-assigned IP address.

12-06  Name Servers

Option:

Function:

IP addresses of Domain Name Servers. Can be automatically assigned when using DHCP.

[0]

Primary DNS

[1]

Secondary DNS

12-07  Domain Name

Range:

Function:

Blank

  [0-19 characters]

Domain name of the attached network. Can be automatically assigned when using DHCP.

12-08  Host Name

Range:

Function:

Blank

  [0-19 characters]

Logical (given) name of option.

12-09  Physical Address

Range:

Function:

  [00:1B:08:00:00:00 – 00:1B:
08:FF:FF:FF]

Read only Displays the Physical (MAC) address of the option.

 

6.2.2 Ethernet Link Parameters

12-1*  Ethernet Link Parameters

Option:

Function:

Applies for whole parameter group.

6 Parameters

MCA 121 EtherNet/IP

36

MG.90.J2.02 - VLT

®

 is a registered Danfoss trademark

6  

Содержание VLT MCA 121 EtherNet/IP






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды