manualshive.com logo in svg

Danfoss VLT MCA 121 EtherNet/IP, Руководство пользователя

Поделиться
Скачать
Danfoss VLT MCA 121 EtherNet/IP Скачать руководство пользователя страница 11

NB!

Please observe that mounting drives of different power-sizes in a line topology may result in unwanted power-off behaviour.
Smaller drives discharge faster than bigger drives. This can result in loss of link in the line topology, which may lead to control word
timeout.
To avoid this, mount the drives with the longest discharge time first in the line topology.

 

AutomationDrive

VLT

AutomationDrive

VLT

AutomationDrive

VLT

AutomationDrive

VLT

AutomationDrive

VLT

½

AutomationDrive

VLT

AutomationDrive

VLT

130BA905.10

Illustration 3.4: Ring/redundant line topology

NB!

For this type of topology it is crucial that the network switch supports Spanning Tree Protocol (STP) or Rapid Spacing Tree (RSTP),
and that STP is enabled. For more information on Spanning Tree please refer to section 

IP traffic

.

 

3.1.5 Network

It is of high importance that the media chosen for Ethernet data transmission are suitable. Usually CAT 5e and 6 cables are recommended for industrial
applications. Both types of cable are available as Unshielded Twisted Pair and Shielded Twisted Pair. Generally shielded cables are recommended for use
in industrial environments and with frequency converters.
A maximum cable-length of 100 m is allowed between switches.

Optical fibres can be used for gapping longer distances and providing galvanic isolation.

For connecting EtherNet/IP devices both hubs and switches can be used. It is, however, recommended always to use suitable industrial graded Ethernet
switches. For more information regarding IP-switching, please refer to section: 

IP Traffic

 in this manual.

MCA 121 EtherNet/IP

3 How to Install

MG.90.J2.02 - VLT

®

 is a registered Danfoss trademark

11

  3

Содержание VLT MCA 121 EtherNet/IP






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды