manualshive.com logo in svg

Danfoss VLT MCA 121 EtherNet/IP, Руководство пользователя

Поделиться
Скачать
Danfoss VLT MCA 121 EtherNet/IP Скачать руководство пользователя страница 10

3.1.4 Topology

The MCA 121 features a build-in Ethernet-switch, thus having two Ethernet RJ-45 connectors. This enables the possibility for connecting several EtherNet/
IP options in a line topology as an alternative to the typical star-topology.

The two ports are equal, in the sense that they are transparent for the option. If only one connector is used, either port can be used.

 

AutomationDrive

VLT

AutomationDrive

VLT

AutomationDrive

VLT

AutomationDrive

VLT

AutomationDrive

VLT

AutomationDrive

VLT

AutomationDrive

VLT

AutomationDrive

VLT

130BA903.10

Illustration 3.2: Star topology

AutomationDrive

VLT

AutomationDrive

VLT

AutomationDrive

VLT

AutomationDrive

VLT

AutomationDrive

VLT

AutomationDrive

VLT

AutomationDrive

VLT

130BA904.10

Illustration 3.3: Line topology

NB!

For line topology please refer to section: “Recommended design rules” In a line topology all drives must be powered, either by mains
or by their 24 V DC option cards, for the build-in switch to work.

3 How to Install

MCA 121 EtherNet/IP

10

MG.90.J2.02 - VLT

®

 is a registered Danfoss trademark

3  

Содержание VLT MCA 121 EtherNet/IP






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды