manualshive.com logo in svg

Danfoss VLT MCA 121 EtherNet/IP, Руководство пользователя

Поделиться
Скачать
Danfoss VLT MCA 121 EtherNet/IP Скачать руководство пользователя страница 17

4.1.3 Configuring the Scanner

EDS file

Danfoss provides a generic English EDS (Electronic Data Sheet) file covering all voltage and power sizes, for off-line configuration.

The EDS file can be downloaded from:
http://www.danfoss.com/BusinessAreas/DrivesSolutions/Softwaredownload/DDFieldbus_Setup_Files.htm

NB!

The current version of the major EtherNet/IP configuration tools does not support EDS-files for EtherNet/IP devices.

Configuring a Rockwell Master

For configuring a FC 200/FC 300 with MCA121 for operation with a Rockwell (Allen-Bradley) Scanner via EtherNet/IP, the FC 200/FC 300 must be added
as a 

Generic Ethernet Module

.

Under the 

General

-tab, enter information about: Name of device, IP Address, Assembly Instance and Data size

NB!

Under 

Configuration

 in the Connection Parameters a “4” must be entered as Assembly Instance.

NB!

Please note that the example shows a 20/70 assembly instance connection. This requires par. 8-10 

Control Profile

 to be set to: ODVA.

Other supported connections are shown in section: 

I/O Assembly Instanced

.

Under the 

Connection

-tab, enter information about: RII and fault conditions.

MCA 121 EtherNet/IP

4 How to Configure

MG.90.J2.02 - VLT

®

 is a registered Danfoss trademark

17

  4

Содержание VLT MCA 121 EtherNet/IP






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды