manualshive.com logo in svg

Danfoss VLT MCA 121 EtherNet/IP, Руководство пользователя

Поделиться
Скачать
Danfoss VLT MCA 121 EtherNet/IP Скачать руководство пользователя страница 16

Par. 12-03, 

Default Gateway

 is optional and only used in routed networks.

Par. 12-06, 

Name Servers

Par. 12-07, 

Domain Name

Par. 12-08, 

Host Name

Are used with Domain Name Server systems and are all optional. If DHCP or BOOTP is selected as IP address assignment, these parameters are read
only.

NB!

It is only possible to assign valid class A, B and C IP address to the option. The valid ranges are shown in the below table:

Class A

1.0.0.1 - 126.255.255.254

Class B

128.1.0.1 - 191.255.255.254

Class C

192.0.1.1 - 223.255.254.254

 

4.1.2 Ethernet Link Parameters

Parameter group 12-1* holds information Ethernet Link information:

12-10

Link Status

12-11

Link Duration

12-12

Auto Negotiation

12-13

Link Speed

12-14

Link Duplex

Please note the Ethernet Link Parameters are unique per port.

Par. 12-10, 

Link Status

 and par. 12-11, 

Link Duration

 displays information on the link status, per port.

Par. 12-10, 

Link Status

 will display Link or No Link according to the status of the present port.

Par. 12-11, 

Link Duration

 will display the duration of the link on the present port. If the link is broken the counter will be reset.

Par. 12-12, 

Auto Negotiation

 – is a feature that enables two connected Ethernet devices to choose common transmission parameters, such as speed and

duplex mode. In this process, the connected devices first share their capabilities as for these parameters and then choose the fastest transmission mode
they both support.
By default this function is enabled.
Incapability between the connected devices, may lead to decreased communication performance.
To prevent this, Auto Negotiation can be disabled.
If par. 12-12 is set to OFF, link speed and duplex mode can be configured manually in par. 12-13 and 12-14.

Par. 12-13, 

Link Speed

 – displays/sets the link speed per port. “None” is displayed if no link is present.

Par. 12-14, 

Link Duplex

 – displays/sets the duplex mode per port.

Half-duplex provides communication in both directions, but only in one direction at a time (not simultaneously).
Full-duplex allows communication in both directions, and unlike half-duplex, allows for this to happen simultaneously.

4 How to Configure

MCA 121 EtherNet/IP

16

MG.90.J2.02 - VLT

®

 is a registered Danfoss trademark

4  

Содержание VLT MCA 121 EtherNet/IP






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды