Danfoss VLT FC 300 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 24

Danfoss VLT FC 300 Скачать руководство пользователя страница 22

6-81 Terminal X45/3 Output Min Scale

Option:

Function:

[0.00%] * 0.00 - 200.00%

Scales the minimum output of the selected analog signal on terminal X45/3. Scale the minimum
value as a percentage of the maximum signal value, i.e. 0 mA (or 0 Hz) is desired at 25% of the
maximum output value and 25% is programmed. The value can never be higher than the corre-
sponding setting in par. 6-82 if value is below 100%.
This parameter is active when option module MCB 113 is mounted in the frequency converter.

6-82 Terminal X45/3 Output Max Scale

Option:

Function:

[0.00%] * 0.00 - 200.00%

Scales the maximum output of the selected analog signal on terminal X45/3. Scale the value to the
desired maximum value of the current signal output. Scale the output to give a lower current than
20 mA at full scale or 20 mA at an output below 100% of the maximum signal value. If 20 mA is
the desired output current at a value between 0 - 100% of the ful-scale output, program the per-
centage value in the parameter, i.e. 50% = 20 mA. If a current between 4 and 20 mA is desired at
maximum output (100%), calculate the percentage value as follows (example where desired max.
output is 10 mA):

IRANGE mA

IDESIRED MAX mA

x 100 % = 20

−

4

mA

10

mA

x 100 % = 160 %

6-83 Terminal X45/3 Output Bus Control

Option:

Function:

[0.00%] * 0.00 - 100.00%

Holds the level of output 4 (X45/3) if controlled by bus.

6-84 Terminal X45/3 Output Timeout Preset

Option:

Function:

[0.00%] * 0.00 - 100.00%

Holds the present level of output 4 (X45/3). In case of a bus timeout and a timeout function is
selected in par. 6-80 the output will preset to this level.

5.4. 14-** 24 V DC External Supply

5.4.1. 14-6* Options

14-80 MCB 113 Supplied by External 24 V DC

Option:

Function:

[0]

No

Select No [0] to use the drive's 24 V DC supply.

[1] *

Yes

Select Yes [1] if an external 24 V DC supply will be used to power the option. I/O will be galvanically
isolated from the drive when operated from an external supply.

5. Parameter Set-up

FC 300 Extended Relay Card Operating In-

structions

22

MI.33.G2.02 - VLT

®

is a registered Danfoss trademark

5

«
...
20
21
22
23
24
»

Содержание VLT FC 300

























Отзывы:

Нет отзывов