manualshive.com logo in svg

Danfoss VLT FC 300, Руководство по эксплуатации, Страница: 11 / 24

Поделиться
Скачать
Danfoss VLT FC 300 Скачать руководство пользователя страница 11

5. Parameter Set-up

5.1. Parameter Set-up

The parameters included in these Operating Instructions are additional parameters for the FC 300 Programming Guide MG.33.MX.YY

5.2. 5-** Digital In/Out

5.2.1. 5-1* Digital Inputs

Parameters for configuring the input functions for the input terminals.
The digital inputs are used for selecting various functions in the frequency converter. All digital inputs can be set to the following functions:

Digital input function

Select

Terminal

No operation

[0]

All *term 32, 33

Reset

[1]

All

Coast inverse

[2]

All *term 27

Coast and reset inverse

[3]

All

Quick stop inverse

[4]

All

DC-brake inverse

[5]

All

Stop inverse

[6]

All

Start

[8]

All *term 18

Latched start

[9]

All

Reversing

[10]

All *term 19

Start reversing

[11]

All

Enable start forward

[12]

All

Enable start reverse

[13]

All

Jog

[14]

All *term 29

Preset reference on

[15]

All

Preset ref bit 0

[16]

All

Preset ref bit 1

[17]

All

Preset ref bit 2

[18]

All

Freeze reference

[19]

All

Freeze output

[20]

All

Speed up

[21]

All

Speed down

[22]

All

Set-up select bit 0

[23]

All

Set-up select bit 1

[24]

All

Precise stop inverse

[26]

18, 19

Precises start, stop

[27]

18, 19

Catch up

[28]

All

Slow down

[29]

All

Counter input

[30]

29, 33

Pulse input

[32]

29, 33

Ramp bit 0

[34]

All

Ramp bit 1

[35]

All

Mains failure inverse

[36]

All

Latched precise start

[40]

18, 19

Latched precise stop inverse

[41]

18, 19

DigiPot Increase

[55]

All

DigiPot Decrease

[56]

All

DigiPot Clear

[57]

All

Counter A (up)

[60]

29, 33

Counter A (down)

[61]

29, 33

Reset Counter A

[62]

All

Counter B (up)

[63]

29, 33

Counter B (down)

[64]

29, 33

Reset Counter B

[65]

All

Mech. Brake Feedb.

[70]

All

Mech. Brake Feedb. Inv.

[71]

All

PTC Card 1

[80]

All

FC 300 standard terminals are 18, 19, 27, 29, 32 and 33. MCB 101 terminals are X30/2, X30/3 and X30/4.
Terminal 29 functions as an output only in FC 302.

Functions dedicated to only one digital input are stated in the associated parameter.

FC 300 Extended Relay Card Operating In-

structions

5. Parameter Set-up

MI.33.G2.02 - VLT

®

 is a registered Danfoss trademark

11

  5

Содержание VLT FC 300

























Отзывы:

Нет отзывов