Danfoss VLT FC 300 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 24

Danfoss VLT FC 300 Скачать руководство пользователя страница 19

5-41 On Delay, Relay

Enter the delay of the relay cut-in time. See par. 5-40.

Array [9]

(Relay 1 [0], Relay 2 [1], Relay 3 [2], Relay 4 [3], Relay 5 [4], Relay 6 [5], Relay 6 [5], Relay

7 [6], Relay 8 [7], Relay 9 [8])

0.01s*

[0.01 - 600.00 s ]

5-42 Off Delay, Relay

Enter the delay of the relay cut-out time. See par. 5-40.

Array [8]

(Relay 1 [0], Relay 2 [1], Relay 3 [2], Relay 4 [3], Relay 5 [4], Relay 6 [5], Relay 6 [5], Relay

7 [6], Relay 8 [7], Relay 9 [8])

0.01s*

[0.01 - 600.00 s.]

If the Selected Event condition changes before the on- or off delay timer expires, the relay output
is unaffected.

5.3. 6-** Analog Outputs

5.3.1. 6-7* Analog Output 3

Parameters for configuring the scaling and limits for analog output 3, Terminal X45/1 and X45/2. Analog outputs are current outputs: 0/4 – 20 mA.
Resolution on analog output is 11 bit.

6-70 Terminal X45/1 Output

Option:

Function:

Select the function of Terminal X45/1 as an analog current output.

[0]

No operation

When no signal on the analog output.

[52]

MCO 305 0-20 mA

[53]

MCO 305 4-20 mA

FC 300 Extended Relay Card Operating In-

structions

5. Parameter Set-up

MI.33.G2.02 - VLT

®

is a registered Danfoss trademark

19

5

«
...
17
18
19
20
21
...
»

Содержание VLT FC 300

























Отзывы:

Нет отзывов