Danfoss H1P 069 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 67

Danfoss H1P 069 Скачать руководство пользователя страница 49

Angle sensor on EDC Repair

D767

D770

1. Clean the exterior of the pump to remove debris.
2. Remove protection cover screws (D767) using a 4 mm internal hex wrench.
3. Remove the protection cover from the control.
4. Discard the protection cover if it is damaged.
5. Remove sensor screws (D770) using a 4 mm internal hex wrench.
6. Remove and discard the sensor.
7. Position a new sensor on control housing.
8. Using a 4 mm internal hex wrench, fasten sensor to control housing with screws (D770). Torque

screws to 1.85 N•m [1.36 lbf•ft].

9. Position protection cover on control housing over sensor.

10. Using a 4 mm internal hex wrench, fasten protection cover with screws (D767). Torque screws to 1.85

N•m [1.36 lbf•ft].

W

Warning

Calibration of sensor output in vehicle software is mandatory after sensor replacement because output
signal can vary from one sensor to the other.

Service Manual

H1P 069—H1P 280 Axial Piston Single Pumps

Minor Repair

©

Danfoss | January 2021

AX152886482551en-000601 | 49

«
...
47
48
49
50
51
...
»

Содержание H1P 069




































































Отзывы:

Нет отзывов