Danfoss H1P 069 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 67

Danfoss H1P 069 Скачать руководство пользователя страница 45

5. Install solenoid with three cap screws (D050) using a 4 mm internal hex wrench and torque screws to

5 N•m [4 lbf•ft].

6. Install coil using a 12 point 27 mm socket and torque coil nut to 5 N•m [3.7 lbf•ft].
7. Reconnect electrical connections and test the pump for proper operation.

Control Solenoids Repair

1. Disconnect electrical connection and remove the three cap screws (D050) using a 4 mm internal hex

wrench.

2. Remove the solenoid (D025) and O-ring (D025A). Discard the O-ring.
3. If necessary, remove the coil using a 12 point 26 mm socket.

Inspect the machined surfaces on the control and top of the pump. If you find any nicks or scratches,

replace the component.

4. Lubricate new O-ring (D025A) using petroleum jelly and install.
5. Install solenoid with three cap screws (D050) using a 4 mm internal hex wrench and torque screws to

5 N•m [4 lbf•ft].

6. Install coil using a 12 point 27 mm socket and torque coil nut to 5 N•m [3.7 lbf•ft].
7. Reconnect electrical connections and test the pump for proper operation.

Service Manual

H1P 069—H1P 280 Axial Piston Single Pumps

Minor Repair

©

Danfoss | January 2021

AX152886482551en-000601 | 45

«
...
43
44
45
46
47
...
»

Содержание H1P 069




































































Отзывы:

Нет отзывов