Danfoss H1P 069 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 67

Danfoss H1P 069 Скачать руководство пользователя страница 42

Servo Adjustment

Servo Adjustment

E350

Servo can

locking bolt

E300

Servo can

locking plate

P106 490E

E300

Servo cylinder clamp

E350

Servo cylinder clamp bolt

1. Run prime mover at 1800 min

-1

(rpm).

2. If using a PWM signal, ensure the signal is off.
3. Check the servo pressure gauges, ensure the differential between M4 and M5 is less than 2.5 bar [36

psi].

4. Using a 3/4 in deep socket, unthread both servo cylinders 2-3 turns.

This step ensures the servo cylinders have no contact with the servo piston.

5. Stroke the pump by turning the control eccentric screw (or supplying current to solenoid C1) until the

servo pressure at port M4 is 1 to 2 bar [14– 29 psi] greater than at port M5 and the system pressure

gauges indicate displacement.

Pressure should be greater at port MA for clockwise rotation, or MB for counterclockwise rotation.
This also indicates the servo piston is in contact with the servo cylinder on side M5.

6. Maintain servo pressure differential between 1-2 bar [14-29 psi] during this step. Slowly thread the

servo cylinder on the M5 side in until the system pressure differential starts to decrease. Continue

turning the servo cylinder in until the system delta pressure results in no machine movement.

System delta pressure (ports MA to MB or MC to MD) between 3-4 bar typically does not cause

machine movement. If service of a pump is not performed on the machine, validation of machine

movement must be checked upon machine start up.

7. Repeat steps 1. to 5. but stroke the pump in the opposite direction by turning the eccentric screw in

the opposite direction, or by supplying current to solenoid C2 to complete setting neutral.

Reverse gauge locations (M4 for M5, MB for MA etc.) from those stated above since the pump is now
stroking the other direction.

8. Set neutral for the rear pump by repeating steps 1. to 6. on the rear pump. Remember that the rear

pump is a mirror image of the front pump and therefore the locations of the servo gauge ports

(M4/M5) and the control solenoids (C1/C2) are opposite.

9. Remove all gauges and replace gauge port plugs.

You can find wrench sizes and plug torques in the

Plug Size and Torque Chart

on page 66.

Service Manual

H1P 069—H1P 280 Axial Piston Single Pumps

Adjustments

42 |

©

Danfoss | January 2021

AX152886482551en-000601

«
...
40
41
42
43
44
...
»

Содержание H1P 069




































































Отзывы:

Нет отзывов