Danfoss H1P 069 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 67

Danfoss H1P 069 Скачать руководство пользователя страница 22

H1 Pumps General Specification

Axial piston closed circuit variable displacement pumps of cradle swash-plate design with clockwise or

counterclockwise direction of rotation.

Pipe connections

•

Main pressure ports: ISO split flange boss

•

Remaining ports: SAE straight thread O-ring boss

Recommended installation position

Pump installation position is discretionary, however the recommended control position is on the top or
at the side with the top position preferred. If the pump is installed with the control at the bottom,
flushing flow must be provided through port M14 located on the EDC, FNR and NFPE control.

Vertical input shaft installation is acceptable. If input shaft is at the top, 1 bar case pressure must be
maintained during operation. The housing must always be filled with hydraulic fluid. Recommended
mounting for a multiple pump stack is to arrange the highest power flow towards the input source.
Consult Danfoss for nonconformance to these guidelines.

Auxiliary cavity pressure

Auxiliary cavity pressure will be inlet pressure with internal charge pump or case pressure with external
charge supply. For reference see Operating Parameters. Please verify mating pump shaft seal capability.

H1P 069—280 Physical Properties

Frame size

069/078, 089/100

115/130, 147/165

210/250/280

Oil volume

2.0 l [0.5 US gal]

3.0 l [ 0.8 US gal]

7.2 l [ 1.9 US gal]

Mounting flange

SAE flange, size C (SAE J

744) mounting pad

SAE flange, size D (SAE J

744) mounting pad

SAE flange, size E (ISO

3019-1 flange 165-4)

mounting pad

Auxiliary mounting

SAE A, SAE B, SAE B-B, SAE

C

SAE A, SAE B, SAE B-B, SAE

C, SAE D

SAE A, SAE B, SAE B-B, SAE

C, SAE D, SAE E

Splined Shafts

•

14-teeth 12/24

•

21-teeth 16/32

•

23-teeth 16/32

•

13-teeth 8/16

•

27-teeth 16/32

•

13-teeth 8/16

•

17-teeth 8/16

•

27-teeth 16/32

Suction port

1.625 [1 5/8] –12UN-2B

Ø38 - 350 bar split flange

boss per ISO 6162

M12x1.75

Main port configuration

Ø25.4 - 450 bar split

flange boss per ISO 6162

M12x1.75

Ø31.5 - 450 bar split

flange boss ISO 6162

M12x1.75

Ø38 - 450 bar split flange
boss ISO 6162
M16x2

Case drain ports L1, L3, L2, L4

(SAE O-ring boss).

0.875 [7/8] -12UNF-2B
1.0625 [1 1/16] -12UNF-2B

1.0625 [1 1/16] -12UNF-2B
1.3175 [1 5/16]-12UNF-2B

Port ISO 11926-1; 1
5/16-12 (SAE O-ring boss)
only L2 and L4

Other ports

SAE O-ring boss

Customer interface threads

Metric fastener

For more info see

Port Locations and Gauge Installation

on page 26

Service Manual

H1P 069—H1P 280 Axial Piston Single Pumps

Technical Specifications

22 |

©

Danfoss | January 2021

AX152886482551en-000601

«
...
20
21
22
23
24
...
»

Содержание H1P 069




































































Отзывы:

Нет отзывов