manualshive.com logo in svg

Danfoss H1P 069, Руководство по обслуживанию, Страница: 3 / 67

Поделиться
Скачать
Danfoss H1P 069 Скачать руководство пользователя страница 3

Introduction

Hydrostatics Servicing Overview................................................................................................................................................ 5

General Servicing Instructions.....................................................................................................................................................5

Safety Precautions............................................................................................................................................................................6

Symbols used in Danfoss literature............................................................................................................................................7

General description of H1 family hydrostatic pumps..........................................................................................................7

Design...................................................................................................................................................................................................8

H1 Single Pumps Closed Circuit Pictorial Diagram............................................................................................................10

H1 system schematic.................................................................................................................................................................... 10

Operation

Pressure Limiter Valves................................................................................................................................................................ 12

Pressure Limiter Sectional View.......................................................................................................................................... 12

High Pressure Relief Valve (HPRV) and Charge Check Valve.......................................................................................... 12

HPRV/Charge Check Valve Sectional View...................................................................................................................... 13

Charge Pressure Relief Valve (CPRV)....................................................................................................................................... 13

Bypass Function..............................................................................................................................................................................13

System Schematic for Single Pump................................................................................................................................... 14

Electrical Displacement Control (EDC)................................................................................................................................... 14

EDC Operation........................................................................................................................................................................... 15

Manual Override (MOR)............................................................................................................................................................... 16

Manual Displacement Control (MDC) ....................................................................................................................................16

MDC Operation..........................................................................................................................................................................17

MDC Torque................................................................................................................................................................................18

Neutral Start Switch (NSS)..................................................................................................................................................... 18

Case Gauge Port M14..............................................................................................................................................................18

Operating Parameters

Input Speed......................................................................................................................................................................................19

System Pressure..............................................................................................................................................................................19

Servo Pressure.................................................................................................................................................................................20

Charge Pressure..............................................................................................................................................................................20

Charge Pump Inlet Pressure.......................................................................................................................................................20

Case Pressure...................................................................................................................................................................................20

External Shaft Seal Pressure....................................................................................................................................................... 21

Temperature.................................................................................................................................................................................... 21

Viscosity.............................................................................................................................................................................................21

Technical Specifications

H1 Pumps General Specification.............................................................................................................................................. 22

H1P 069—280 Physical Properties...........................................................................................................................................22

Fluid Specification......................................................................................................................................................................... 23

Fluid and Filter Maintenance Recommendations

Filtration System.............................................................................................................................................................................24

Pressure Measurements

Port Locations and Gauge Installation................................................................................................................................... 26

H1P Ports Information.............................................................................................................................................................26

Initial Startup Procedures

Unintended Machine Movement.............................................................................................................................................28

Start-Up Procedure........................................................................................................................................................................28

Troubleshooting

High Inlet Vacuum......................................................................................................................................................................... 30

Unintended Machine Movement....................................................................................................................................... 30

Fluid Under Pressure............................................................................................................................................................... 30

Electrical Troubleshooting..........................................................................................................................................................30

Integral Filter Bypass.....................................................................................................................................................................30

Neutral Difficult or Impossible to Find................................................................................................................................... 31

Transmission Operates Normally in One Direction Only.................................................................................................31

Service Manual

H1P 069—H1P 280 Axial Piston Single Pumps

Contents

 

©

 Danfoss | January 2021

AX152886482551en-000601 | 3

Содержание H1P 069




































































Отзывы:

Нет отзывов