Danfoss H1P 069 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 67

Danfoss H1P 069 Скачать руководство пользователя страница 57

11. Remove the protective cover.

Seal Installation Tool

55 mm

[2.17 in]

120 mm

[4.72 in]

078/089/100

78 mm

[3.07 in]

82 mm

[3.23 in]

115/130
147/165

7 mm

[0.28 in]

51 mm

[2. in]

68.5 mm

[2.70 in]

50°

80°

44.7 mm

[1.76 in]

89.4 mm

[3.52 in]

7 mm

[0.276 in]

78 mm

[3.07 in]

75.6 mm

[2.97 in]

210/250/280

4.4 mm

[0.17 in]

80°

57.5 mm

[2.26 in]

89.4 mm

[3.52 in]

12. Install the remaining snap ring (J200).

External Filter Repair

T015
24mm

P106 035E

T150

T035

T045

1. With the prime mover off, hold the filter (T150) in place, and remove the plug (T015) using a 24 mm

wrench.

2. Remove the filter.
3. Remove and discard the seal (T045) and O-ring (T035).
4. Inspect the plug and sealing surfaces in the filter bracket.
5. Replace any damaged components.
6. Install new seal (T045) and O-ring (T035) on plug.
7. Apply hydraulic fluid to the O-ring and seal for lubrication.
8. Insert the plug into the bracket.
9. Use a 24 mm wrench to hold the plug in place and install the replacement filter.

Hand tighten filter till it contacts O-ring, then tighten 1/2 turn further.

10. Start the prime mover.

Cycle the pump through normal machine operation and check for leaks.

Service Manual

H1P 069—H1P 280 Axial Piston Single Pumps

Minor Repair

©

Danfoss | January 2021

AX152886482551en-000601 | 57

«
...
55
56
57
58
59
...
»

Содержание H1P 069




































































Отзывы:

Нет отзывов