Danfoss H1B 060 Скачать руководство пользователя | Manualshive

Страница: 51 / 68

background image

Electric two-position control module

Coil O-rings are not included in the overhaul seal kit. They are included with the purchase of a new coil.

Disassembly

1. Use a 26 mm 12-point socket to remove coil nuts (B0026) and O-ring (B0028).
2. Remove coils (B0022) and O-rings (B0024). Discard O-rings.
3. Using a 17 mm open-end wrench on the flats provided, remove solenoid assemblies (B0032).
4. Remove and discard O-rings (B0034).
5. Using a 1/8 inch internal hex wrench, remove four plugs (C0060). Remove and discard O-rings

(C0060A).

6. Using a 1/4 inch internal hex wrench, remove two plugs (C0050). Remove and discard O-rings

(C0050A).

7. Using a 17 mm hex wrench, remove pressure compensator adjusting plug (C0090). Remove and

discard O-ring (M223).

8. Remove springs (C0030) and (C0080). Remove spools (C0020) and (C0070).
9. If necessary, use a 3 mm internal hex wrench to remove orifices (E00T2) and (E00T3).

Inspection
Clean and inspect the machined surfaces on the control and the endcap. If any nicks or scratches are
found, replace the control/endcap assembly.

Service Manual

H1 Bent Axis Motors, Size 060/080/110/160/210/250 cm3

Minor repair

©

Danfoss | August 2018

AX00000025en-US0504 | 51

«
...
49
50
51
52
53
...
»

Содержание H1B 060





































































Отзывы:

Нет отзывов

Похожие инструкции для H1B 060

StarDental Titan-E

Бренд: DentalEZ Страницы: 2

Бренд: YOODA Страницы: 7

Бренд: fadini Страницы: 56

Бренд: Newland Страницы: 29

Бренд: Baldor Страницы: 1

Бренд: Nouvag Страницы: 8

Бренд: Toro Страницы: 96

Бренд: Yanmar Страницы: 2

Бренд: Yanmar Страницы: 2

Бренд: Yanmar Страницы: 48

Бренд: Honda Страницы: 193

Бренд: Erfal Страницы: 8

NEWTON ACM EUROTITAN CL

Бренд: Xl Automatismos Страницы: 4

Бренд: Asmo Marine Страницы: 8

Бренд: Universal Страницы: 124

Бренд: Helios Страницы: 16

Бренд: Ford Страницы: 42

Бренд: Ford Страницы: 71

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды