Danfoss H1B 060 Скачать руководство пользователя | Manualshive

Страница: 10 / 68

background image

General description

Series H1 variable displacement motors are bent axis design, incorporating spherical pistons.

These motors are designed primarily to be combined with other products in closed circuit systems to
transfer and control hydraulic power. Series H1 motors have a large maximum/minimum displacement
ratio of 5:1 and high output speed capabilities.

The expanded function of zero degree capability, coupled with a high performance 32 degree maximum
angle, creates opportunities to easily improve the machine performance for:

•

Wheel assist on the steering axle of high inertia machines (i.e. combines) and could include Anti Slip
Control

•

Off-highway machines requiring Anti Slip Control (i.e. Ag. sprayer)

•

Multi-motor applications requiring optimized work and transport modes (i.e. wheel loader, Ag
sprayer) utilizing the zero degree position for maximum transport speed

•

Improved machine (i.e. single drum roller) gradeability through precise Anti Slip Control

The Anti Slip Control reduces ground damage, increases traction control and improves machine
controllability for the operator.

SAE, Cartridge (not available for 210 cm

3

and 250 cm

3

) and DIN (not available for 250 cm

3

) flange with

radial or axial high pressure port configurations are available including the loop flushing device.

A complete family of controls and regulators are available to fulfill the requirements of a wide range of
applications.

Motors normally start at maximum displacement. This provides maximum starting torque for high
acceleration.

All controls utilize internally supplied servo pressure. This may be overridden by a pressure compensator
which functions when the motor is operating in motor and pump modes. A defeat option is available to
disable the pressure compensator override when the motor is running in pump mode during
deceleration/braking.

The pressure compensator option features a low pressure rise to ensure optimal power utilization
throughout the entire displacement range of the motor.

Speed sensor options are available to cover all frame sizes and flange styles.

They are capable of sensing the following, all in one package:

•

Speed

•

Direction (only group "J", option "S")

•

Temperature (only group "J", option "S")

The electric controls are specifically designed for the Danfoss family of PLUS+1

®

microcontrollers for

easy "Plug and Perform" installation.

Service Manual

H1 Bent Axis Motors, Size 060/080/110/160/210/250 cm3

H1 general information

10 |

©

Danfoss | August 2018

AX00000025en-US0504

«
...
8
9
10
11
12
...
»

Содержание H1B 060





































































Отзывы:

Нет отзывов

Похожие инструкции для H1B 060

Бренд: YOODA Страницы: 7

Бренд: RHINO MOTION CONTROLS Страницы: 4

Бренд: Danfoss Страницы: 32

WEST EUROTECH 36 T2

Бренд: Weston UK Страницы: 3

Бренд: Magnetic Страницы: 24

Бренд: Northern Lights Страницы: 36

Бренд: Northern Lights Страницы: 45

Бренд: Northern Lights Страницы: 56

Бренд: Bison Страницы: 19

Бренд: Volvo Penta Страницы: 136

RolloTube S-line DuoFern

Бренд: RADEMACHER Страницы: 8

RolloTube Basis

Бренд: RADEMACHER Страницы: 60

Бренд: RADEMACHER Страницы: 64

Бренд: Volvo Страницы: 8

Бренд: Detroit Diesel Страницы: 40

Бренд: Honda Страницы: 2

Бренд: O.S. engine Страницы: 9

Бренд: O.S. engine Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды