Danfoss H1B 060 Скачать руководство пользователя | Manualshive

Страница: 35 / 68

background image

Optional threshold adjustment – Electric proportional controls

Adjusting threshold on test stand

1. Connect flow meter to A or B system port. Refer to

Ports and Gauge Information

on page 26 for port

locations.

2. Connect solenoid to PWM signal generator at 150 Hz.

Threshold is the electric signal when the motor starts to change from maximum to minimum

displacement.

3. Run prime mover at operating speed.

Threshold adjustment

B0040

adjusting

screw

3 mm

4. Adjust PWM signal to current listed in model code. Note flow reading.
5. 5. If adjustment is necessary, remove cap (B0040). Using a 3mm internal hex wrench, turn adjusting

screw clockwise or counterclockwise until flow starts to change from maximum. Test your adjustment

by lowering the current, then increasing the current until the displacement starts to change. Readjust

the setting if necessary.

6. When threshold is adjusted correctly, stop prime mover, install cap (B0040), and install motor on

vehicle. Run vehicle and test for proper motor operation.

Adjusting threshold on a machine or test stand without flow meter

1. Install 600 bar [10,000 psi] gauges to ports M5 and M4. Connect solenoid to PWM signal.
2. Raise wheels off ground, or disconnect the work function.

W

Warning

Unintended movement of the machine or mechanism may cause injury to the technician or

bystanders. To protect against unintended movement, secure the machine or disable/disconnect the

mechanism while servicing.

3. Run prime mover at operating speed. Stroke the pump to get some rotation of motor shaft.
4. Increase signal current until M4 pressure becomes 1/2 of the M5 pressure. Check the signal current at

this point.

5. If adjustment is necessary, remove cap (B0040). Turn the adjusting screw until the signal current

matches the model code setting.

6. When threshold is adjusted correctly, stop prime mover, install cap. Run vehicle and test for proper

motor operation.

7. Remove from test stand.

Service Manual

H1 Bent Axis Motors, Size 060/080/110/160/210/250 cm3

Adjustments

©

Danfoss | August 2018

AX00000025en-US0504 | 35

«
...
33
34
35
36
37
...
»

Содержание H1B 060





































































Отзывы:

Нет отзывов

Похожие инструкции для H1B 060

Бренд: Ofna Racing Страницы: 2

Бренд: Yanmar Страницы: 104

Бренд: Briggs & Stratton Страницы: 6

Бренд: Westerbeke Страницы: 64

Бренд: Northern Lights Страницы: 36

Бренд: Northern Lights Страницы: 45

Бренд: Northern Lights Страницы: 56

Бренд: EX Model Engines Страницы: 2

Бренд: Nederman Страницы: 44

Бренд: Jets Munt Страницы: 24

Бренд: SPE Страницы: 7

Бренд: TEM Страницы: 19

75-200 V DC Series

Бренд: TEM Страницы: 38

Бренд: TEM Страницы: 42

Бренд: Winterthur Gas Страницы: 495

Бренд: Daewoo Страницы: 165

Бренд: Sanyo Denki Страницы: 20

Бренд: B&R Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды