Danfoss H1B 060 Скачать руководство пользователя

Страница: 22 / 68

Speed sensor

The speed sensor is designed for rugged outdoor, mobile or heavy industrial speed sensing applications.

The detection of the speed is contactless and does not need any calibration or adjustments.

For more information, see

Speed and Temperature Sensor, Technical Information,

11046759.

Sensor position
Sensor position in SAE, DIN and Cartridge housing.

SAE and DIN housing

P003450

Cartridge housing

P003489

Target Ring
Speed (target) rings vary according to the diameter of the cylinder block or shaft on which they are

installed. The number of teeth is shown in the table below.

The number of speed (target) ring teeth

H1B size

060

080

110

160

210

250

Teeth

104

108

Excessive axial shaft loading during installation of motors with speed sensors and cartridge housings
must be avoided. High axial shaft loads during installation of motors can lead to a movement of the shaft
and damage the speed sensor.

Displacement limiter

All Series H1 motors incorporate mechanical displacement limiters.

The minimum displacement of the motor is preset at the factory with a set screw in the motor housing.
A tamper-proof cap is provided.

Service Manual

H1 Bent Axis Motors, Size 060/080/110/160/210/250 cm3

Operation

22 |

Danfoss | August 2018

AX00000025en-US0504

Содержание H1B 060





































































Результаты поиска

Содержание H1B 060

Отзывы:

Похожие инструкции для H1B 060

Бренды по названию

Популярные бренды

Danfoss H1B 060, Руководство по обслуживанию

Результаты поиска

Содержание H1B 060

Отзывы:

Похожие инструкции для H1B 060

Бренды по названию

Популярные бренды