Danfoss H1B 060 Скачать руководство пользователя | Manualshive

Страница: 63 / 68

background image

Loop flushing spool

Removal

1. Remove plugs (K0030) using a 24 mm hex wrench.
2. Remove and discard O-rings (K0030A).
3. Use a magnet to remove springs (K0020) and spool (K0010).

Inspection
Clean and inspect spool (K0010). If spool is damaged or worn replace it. Replace springs if they are
cracked or bent.

Reassembly

Loop flushing reassembly

K0010

K0030

K0030A

K0020

K0030

K0030A

K0020

67 N•m
[49 lbf•ft]

67 N•m [49 lbf•ft]

24 mm

24 mm

1. Lubricate and install spool (K0010).
2. Lubricate and install springs (K0020).
3. Lubricate and install new O-rings (K0030A).
4. Install plugs (K0030) using a 24 mm hex wrench with torque to 67 N•m [49 lbf•ft].

Service Manual

H1 Bent Axis Motors, Size 060/080/110/160/210/250 cm3

Minor repair

©

Danfoss | August 2018

AX00000025en-US0504 | 63

«
...
61
62
63
64
65
...
»

Содержание H1B 060





































































Отзывы:

Нет отзывов

Похожие инструкции для H1B 060

Бренд: Waukesha Страницы: 142

Бренд: Beta Marine Страницы: 88

Бренд: Vascat Страницы: 60

Бренд: YuanDong Страницы: 23

HO Union Pacific

Бренд: MTHTrains Страницы: 31

Бренд: Perkins Страницы: 108

Бренд: Sanshin Страницы: 25

Бренд: Lombardini Страницы: 88

Бренд: Omron Страницы: 18

Бренд: Omron Страницы: 438

Бренд: Robin America Страницы: 31

Бренд: O.S. engine Страницы: 38

Бренд: ST Страницы: 281

Бренд: Agrimate Страницы: 32

Бренд: Krick Страницы: 12

116-BOXER IRS - V1.7

Бренд: MVVS Страницы: 6

Бренд: Toyota Страницы: 608

Бренд: HPI Racing Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды