Danfoss H1 Series Скачать руководство пользователя страница 51

Страница: 51 / 72

Inspection

Inspect the machined surfaces on the control and top of the pump. If you find any nicks or scratches,
replace the component.

Reassembly

Ensure you install dowel pins (D300) in the housing before installing the control.

1. Install a new gasket (D150).
2. Install dowel pins (D300) in the housing.

Warning

If the feedback pin comes off during operation, the pump will lose controllability causing a

potentially hazardous situation. Insure feedback pin is properly torqued before continuing with

reassembly.

3. If you removed screen (D084), install a new one. Install it with the mesh facing outward (see drawing).

Install retaining ring (D098).

MDC - Proper screen orientation

D084

Incorrect screen

orientation

Correct screen

orientation

D098

4. If previously removed, install orifices using a 3 mm internal hex wrench. Torque to 2.5 Nm [1.8 lbf ft].

Remove the plug on top of the control to ensure the swashplate feedback pin is properly positioned

in the center of the control module when installing control.

5. Install the control module and six cap screws (D250).

Torque sequence

6. Using a 5 mm internal hex wrench, torque the cap screws (D250) to 13.3 Nm [9.8 lbf ft].

Service Manual

H1 45/53/60/68 Tandem Closed Circuit Axial Piston Pumps

Minor repair

Danfoss | June 2018

520L0928 | AX00000103en-US0303 | 51

Содержание H1 Series









































































Результаты поиска

Содержание H1 Series

Отзывы:

Похожие инструкции для H1 Series

Бренды по названию

Популярные бренды

Danfoss H1 Series, Руководство по обслуживанию

Результаты поиска

Содержание H1 Series

Отзывы:

Похожие инструкции для H1 Series

Бренды по названию

Популярные бренды