Danfoss H1 Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 72

background image

MDC Torque

Description

Value

Torque required to move handle to maximum displacement

1.4 N•m [12.39 lbf•in ]

Torque required to hold handle at given displacement

0.6 N•m [5.31 lbf•in]

Maximum allowable input torque

20 N•m [177 lbf•in]

C

Caution

Volumetric efficiencies of the system will have impacts on the start and end input commands.

MDC General Information
In difference to other controls the MDC provides a mechanical deadband. This is required to overcome
the tolerances in the mechanical actuation.

The MDC contains an internal end stop to prevent over travel. The restoring moment is appropriate for
turning the MDC input shaft back to neutral only. Any linkages or cables may prevent the MDC from
returning to neutral.

The MDC is designed for a maximum case pressure of 5 bar and a rated case pressure of 3 bar. If the case
pressure exceeds 5 bar there is a risk of an insufficient restoring moment. In addition a high case pressure
can cause the NSS to indicate that the control is not in neutral. High case pressure may cause excessive
wear.

Customers can apply their own handle design but they must care about a robust clamping connection
between their handle and the control shaft and avoid overload of the shaft.

Customers can connect two MDC’s on a tandem unit in such a way that the actuation force will be
transferred from the pilot control to the second control but the kinematic of the linkages must ensure
that either control shaft is protected from torque overload. To avoid an overload of the MDC, customers
must install any support to limit the setting range of the Bowden cable.

C

Caution

Using the internal spring force on the input shaft is not an appropriate way to return the customer

connection linkage to neutral.

Neutral Start Switch (NSS)
The Neutral Start Switch (NSS) contains an electrical switch that provides a signal of whether the control
is in neutral. The signal in neutral is Normally Closed (NC).

Neutral Start Switch schematic

P005 702

M14

M5

M4

M3

Service Manual

H1 45/53/60/68 Tandem Closed Circuit Axial Piston Pumps

Operation

16 |

©

Danfoss | June 2018

520L0928 | AX00000103en-US0303

«
...
14
15
16
17
18
...
»

Содержание H1 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для H1 Series

Бренд: Danfoss Страницы: 34

Бренд: Danfoss Страницы: 52

Бренд: ULTIMATE SPEED Страницы: 52

Fybroc series 1530

Бренд: Met-Pro Страницы: 22

Бренд: Nortek Страницы: 52

TURBOPOWER 1000 P 225A-TPL

Бренд: PVI Industries Страницы: 1

Q HEAT R Series

Бренд: CANVAC Страницы: 88

Aqua-Pure 3MFF100

Бренд: 3M Страницы: 8

Бренд: BLACKMER Страницы: 14

Бренд: Wacker Neuson Страницы: 50

Бренд: Solar Energy Страницы: 4

Clean Jet 800 Plus + Kit

Бренд: T.I.P. Страницы: 140

Comfort Solutions 1900e Series

Бренд: Taco Страницы: 12

Бренд: Bestway Страницы: 12

Бренд: Daikin Страницы: 36

Бренд: ProMinent Страницы: 32

Бренд: SFA Страницы: 32

Бренд: FRIGOMAR Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды