Danfoss H1 Series Скачать руководство пользователя страница 54

Страница: 54 / 72

4. Pull assembly fixture out before installing control screws.

Solenoid shaft

Feedback pin

Adjusting

screw

(cam)

Maximum

adjustment

less than 120°

Control spool

Remove plug (D065) and verify the swashplate feedback pin is properly positioned between control

feedback arms.

5. Using a 5 mm internal hex wrench, fasten control to pump with screws (D250). Torque screws to 13.5

N•m [10 lbf•ft] following torque sequence shown.

Torque sequence

(6 screw control)

D065

Warning

Calibration of sensor output in vehicle software is mandidtory after sensor replacement because

output signal can vary from one sensor to the next.

For proper neutral adjustment procedure, refer to

Control Neutral Adjustment

topic

Front Shaft, seal, and bearing

The front pump input shaft assembly is serviceable without disassembling the pump, the rear shaft is not.
Orient the pump on the work surface so the shaft is pointing to the side.

Removal

1. Remove the retaining ring (J300) from the housing to release the shaft/seal/bearing subassembly.

Service Manual

H1 45/53/60/68 Tandem Closed Circuit Axial Piston Pumps

Minor repair

54 |

Danfoss | June 2018

520L0928 | AX00000103en-US0303

Содержание H1 Series









































































Результаты поиска

Содержание H1 Series

Отзывы:

Похожие инструкции для H1 Series

Бренды по названию

Популярные бренды

Danfoss H1 Series, Руководство по обслуживанию

Результаты поиска

Содержание H1 Series

Отзывы:

Похожие инструкции для H1 Series

Бренды по названию

Популярные бренды